General Information
Safety Precautions
• Use this product indoors. It should not be used outdoors.
• This products is designed to be powered over Ethernet cabling.
• When installing the equipment, all the requirements of the
manufacturer and the referenced standards must be met.
• There are no user serviceable parts inside.
• CAUTION: Changes or modifications to this product not expressly
approved by Nextivity may void your right to operate the equipment.
Warranty
Nextivity Inc. provides a limited warranty for its products. For details,
please refer to
www.cel-fi.com/warranty
.
Limitation of Liability
In no event shall Nextivity, nor its directors, employees, agents,
suppliers or End Users, be liable under contract, tort, strict liability,
negligence or any other legal or equitable theory with respect to the
Products or any other subject matter of this Agreement (i) for any lost
profits, cost of procurement of substitute goods or services, or
special, indirect, incidental, punitive, or consequential damages of any
kind whatsoever or (ii) for any direct damages in excess of (in the
aggregate) the fees actually received by Nextivity from End User with
respect to the Products actually purchased and paid for.
See
www.cel-fi.com
for list of patents covering this product.
Electromagnetic Compatibility (EMC)
This equipment has been designed and tested to fulfill applicable
standards for:
• Radio frequency emission when installed according to the
instructions and used in its intended environment.
• Immunity to electrical and electromagnetic phenomena when
installed according to the instructions and used in its intended
environment.
USA
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV/IT technician for help.
Europe
1
2
ITEM
Model
Data Rate
Connectors
Cabling
INPUT/OUTPUT voltage
Power Consumption
Device Type
Ambient Operating Temp
Relative humidity
Environment
Mounting
Dimensions
Weight
Compliance
SPECIFICATION
Q40-OE
1000 Mbps full duplex
RJ45
Category 5e or better
42 - 57 VDC
7.5 watts typ.
Class II
0 – 40ºC
0 – 95% Non-condensing
Indoors
Wall or shelf
150 (L) x 110.5 (W) x 78 (H) mm
0.7 kg
FCC Part 15, Class B
CE
IEEE 802.3at-2009
RoHS
UL/CSA/EN 62368-1
Technical Specifications:
Cel-Fi QUATRA 4000 Range Extender
CEL-FI QUATRA ACCESSORY
Cel-Fi QUATRA Range Extender cables from the Cel-Fi QUATRA Network
Unit (NU) to the Coverage Unit (CU) must be dedicated.(proprietary data
link)! The system will not function if common shared LAN resources are
used with cabling (routers, switches etc).
Cel-Fi QUATRA Range Extender heat sink edges may be sharp.
Caution while handling.
STEP 2:
Connect INPUT and OUTPUT cabling
• Extender power is provided by the cables from the Cel-Fi QUATRA
NETWORK UNIT.
• RJ45 LED #1 (solid amber) indicates power.
• RJ45 LED #2 will blink green during initialization, and will be solid
green when the Extender has passed self-test and is operating
normally.
• If both LEDs blink off periodically on a port, the port is resetting to
try and establish communications with the Cel-Fi QUATRA
NETWORK UNIT or Cel-Fi QUATRA COVERAGE UNIT it is
connected to. Check cables and connections if this occurs.
• If both INPUT LEDs are off, check the cable to the Cel-Fi QUATRA
NETWORK UNIT and that the NETWORK UNIT is powered up.
• If both OUTPUT LEDs are off, check the cable to the Cel-Fi QUATRA
COVERAGE UNIT.
• For further assistance, please consult your installer or contact
http://www.cel-fi.com/support
.
Compliance Contact
In the event of a regulatory compliance issue, please contact Nextivity
Inc. at
www.nextivityinc.com
.
Note: Certifications are regional; not all products need or have the
same certifications. Please check the specific model number to
determine exactly which certifications it has.
Patents
This product is covered by Nextivity, Inc., US patents and patents
pending. Please refer to
www.cel-fi.com
for details.
Support
Should you require any assistance, please contact your Cel-Fi
QUATRA reseller. If your questions cannot be answered immediately,
your reseller will forward your queries through the appropriate
channels to ensure a rapid response. If you still need assistance visit:
http://www.cel-fi.com/support
.
Copyright © 2019 by Nextivity, Inc, U.S. Patents pending. All rights reserved. The Nextivity
and Cel-Fi logos are registered trademarks of Nextivity Inc. All other trademarks or
registered trademarks listed belong to their respective owners. Designed by Nextivity
Inc in California.
manual-quatra-4000-ext_19-1111
Installation
STEP 1:
Locate and mount the Extender unit
• Input and Output port LEDs should be clearly visible.
• Allow adequate ventilation.
• Do not mount in direct sunlight, near heat sources, or in weather
exposed areas.
• The Cat 5e cables (or better) that connect the INPUT ports to the
Cel-Fi QUATRA NETWORK UNIT should not exceed 100 meters in
length.
• The Cat 5e cables that connect the OUTPUT port to the Cel-Fi
QUATRA COVERAGE UNIT should not exceed 100 meters in length.
