CEECO SSW-321-Dr1 Service Manual Download Page 10

ISSUE 4.0 

CEECO 

Communication Equipment & Engineering Company 

PROPRIETARY 

10 

9.0    FCC NOTICE 

 
 

9.1  

FCC REGISTRATION AND REPAIR INFORMATION 

 

Your new telephone has been registered with the Federal Communication 
Commission (FCC) in accordance with Part 68 of its rules.  The FCC 
requires that you be advised of certain requirements involving the use of 
this telephone. 

 

9.2  

CONNECTION WITH THE NATIONWIDE TELEPHONE 
NETWORK 

 

The FCC requires that you connect this telephone to the Nationwide 
Telephone Network through a registered jack provided by the telephone 
company in your area.  This jack is a  modular outlet, which you can order 
from your local telephone company. 

 
 

9.3  

NOTIFICATION TO THE TELEPHONE COMPANY 

 

Before connecting this telephone, the FCC requires that you notify your 
local telephone company business office.  The number is in the front of 
your phone book. 

 
 

 

Tell them: 

 

The "line" to which you will connect the telephone (that is, your phone 
number) and the telephone's FCC registration number and ringer 
equivalence number.  These numbers are listed in section 8.0. 

 

The FCC further requires that you notify your local telephone company 
when permanently disconnecting this telephone.

Summary of Contents for SSW-321-Dr1













Reviews: