background image

8

A. RESET MASTER CODE 

   AND USER CODES

 

 

1.  Enter the master code twice    

 

 

(1 2 3 4 5 default value master code). 

       

2 beeps are emitted to confi rm  

 

 

entry in programming mode.

 2. 

Press A6 to reset the Master Code  

 

 

and the User codes. 

 

 

One beep is emitted. Press on A 

   and 

B to confi rm reset of all memory 

 

 

of the keypad. Wait for two beeps.  

 

 

The master code is restored 

 

 

to its default value 1 2 3 4 5 

 

 

and all the User codes are deleted  

 

 

from the keypad. Once the reset 

 

 

is completed then the keypad returns  

 

 

to a stand-by operating mode.

OR

 

1.  Cut the power. Put the jumper on P2. 

 

2.   Put the power back. 

 

 

Wait approximately 3 seconds. 

 

 

Two beeps are emitted to confi rm reset  

 

 

of the keypad. Remove P2 jumper.  

 

 

The master code is restored to its default  

   value 

1 2 3 4 5 and all the User codes 

 

 

are deleted from the keypad.

B. SETTING CODE LENGTH

 

1.  Enter the master code twice.   

 

 

(1 2 3 4 5 default value master code).  

 

 

2 beeps are emitted to confi rm    

 

 

entry in programming mode.

 

2.  Press A4 to program the code length.

 

 

One beep is emitted. Press 4 or 5   

 

 

for the digit code. One beep is emitted  

   to 

confi rm programming of the code length. 

 

3.  Press A5 to modify the master code.  

 

 

One beep is emitted. Enter the new 4  

 

 

or 5-digit master code. One beep is  

 

 

emitted to confi rm programming 

 

 

of the new master code. 

 

 

4.  Press B to exit from 

   programming 

mode.

 

 

2 beeps are emitted to confi rm that the key- 

 

 

pad is in stand-by operating mode.

4 beeps indicate a data computing error.

C. CHANGING THE MASTER CODE

   

The master code is used only 

 

 

to enter in programming mode.

 

1.  Enter the master code twice.   

 

 

(1 2 3 4 5 default value master code). 

 

 

2 beeps are emitted to confi rm    

 

 

entry in programming mode.

 2. 

Press A5 to modify the master code.  

 

 

One beep is emitted. Enter the new 4  

 

 

or 5 digit master code. One beep 

 

 

is emitted to confi rm that the master  

 

 

code is programmed.

 

3.  Press B to exit from 

 

 

the programming mode. 

 

 

2 beeps are emitted to confi rm that the key- 

 

 

pad is in stand-by operating mode.

Default values

- Without codes.

 

- Illumination time: 10 seconds

- Relay release time: 1 second.

- Code length: 5-digit. 

- Master Code: 1 2 3 4 5.

- Programming security time : 

  120 secondes.

- Code length for sub master code:

 

 

Version 1 relay (Group 1) = 

  A and B,

 

 Version 2 relays (Group 2) =    

  1 and 3

 

 Version 3 relays (Group 3) = 

  4 and 6.

 

Audible signal:

The buzzer indicates different audible 

signals. It can be turned off by cutting 

the ST1 wire on the remote controller

1 short beep: Keypad powered

1 long beep: Data computing 

in programming or access granted

2 short beeps: Enter or Exit 

from programming

4 short beeps: 

Data computing error.

Code length

The master code and the User codes 

can be of 4 or 5-digit in length.

All the keypad keys can be used 

to program a code. The master code 

and the Pin code can be of 4 or 5-digit 

code. The master code CAN NOT 

be used as a PIN code (User Pin code). 

The master code CAN NOT be used 

as a PIN code (User Pin code). 

To delete a specifi c User pin Code replace 

it by 0000 if code length is 4-digit format 

or replace it by 00000 if the code 

is in 5-digit format.

P2 jumper: 

Reset master code and user codes

P3 jumper: 

modifi cation of individual 

code by the user

KCIN

Illuminated weatherproof Keypad with Remote Electronics 1, 2 or 3 relays

 INSTALLATION MANUAL

8

cdvi.com

cdvigroup.com

Summary of Contents for Digicode KCIN

























Reviews: