manualshive.com logo in svg

CDA WC140, Manual For Installation, Use And Maintenance

Share
Download
CDA WC140 Manual For Installation, Use And Maintenance Download Page 12

Failure Codes and Troubleshooting

Your dishwasher control panel is equipped with a diagnostic display to help in the event of a problem with the appliance.

Error Code

Error description

Advice

Intensive

Normal

Eco

Quick

Prewash

Inadequate water 

supply

Make sure the water inlet tap is 

fully open

Close the water tap, separate the 

water inlet hose from the tap and 

clean the filter

Restart your machine, contact 

CDA service if the error resumes

Continual fill error

Close the tap and contact 

CDA service

The waste water in 

the machine cannot 

be discharged.

Drain hose is blocked

The filters of your machine 

might be blocked

Restart the dishwasher and 

cancel the programme

If the error continues, contact 

CDA service

Heater error

Contact CDA service

Alarm is active against 

water overflow

Turn off the dishwasher and 
disconnect the water supply

Contact CDA service

Faulty electronic card

Contact CDA service

Overheating error 

(temperature in the 

machine is too high)

Contact CDA service

Faulty heater sensor

Contact CDA service

Summary of Contents for WC140



















Reviews:

No comments

Brands by name

Popular brands

Load more brands