CDA RC 9301 Manual For Installation, Use And Maintenance Download Page 29 | Manualshive

Page: 29 / 44

background image

29

Gas installation

IMPORTANT NOTE

This appliance is supplied for use on NATURAL GAS or LPG (check the gas regulation
label attached on the appliance).

✓

Appliances supplied for use on NATURAL GAS: they are adjusted for this gas only and
cannot be used on any other gas (LPG) without modification. The appliances are
manufactured for conversion to LPG.

✓

Appliances supplied for use on LPG: they are adjusted for this gas only and cannot
be used on any other gas (NATURAL GAS) without modification. The appliances are
manufactured for conversion to NATURAL GAS.

If the NATURAL GAS/LPG conversion kit is not supplied with the appliance this kit can
be purchased by contacting the After-Sales Service.

INSTALLATION & SERVICE REGULATIONS (UNITED KINGDOM)

It is a legal requirement that all gas appliances are Installed & Serviced by a competent
person in accordance with the current editions of the following Standards &
Regulations or those regulations appropriate to the geographical region in which they
are to be installed:

✓

Gas Safety (Installation & Use) Regulations

✓

Building Regulations

✓

British Standards

✓

Regulations for Electrical Installation

Installation  and  service  of  any  gas  product  must  be  made  by  a  suitably  qualified  and
registered  person  competent  on  the  type  of  product  being  installed  or  serviced  and
holding a valid certificate of competence for the work being carried out. Currently the
proof  of  competence  is  the  Accredited  Certification  Scheme  (ACS)  or  S/NVQ  that  has
been aligned to the ACS.

It is also a requirement that all businesses or self employed installers are members of a
class of person approved by the Health and Safety Executive.

Failure to install the appliance correctly could invalidate any manufacturers warranty
and lead to prosecution under the above quoted regulation.

«
...
27
28
29
30
31
...
»

Summary of Contents for RC 9301













































Reviews:

No comments

Related manuals for RC 9301

Brand: GE Pages: 2

36 ELECTRIC RADIANT COOKTOP ZEU36R

Brand: GE Pages: 8

36 Ceramic Cooktop

Brand: GE Pages: 16

Brand: GE Pages: 80

Brand: GE Pages: 32

Brand: GE Pages: 16

Brand: GE Pages: 32

Brand: GE Pages: 2

Brand: GE Pages: 38

Brand: GE Pages: 64

Brand: GE Pages: 16

Brand: GE Pages: 8

Brand: GE Pages: 48

36 ELECTRIC RADIANT COOKTOP ZEU36R

Brand: GE Pages: 4

Brand: GE Pages: 24

Brand: GE Pages: 36

Brand: GE Pages: 16

Brand: Rangemaster Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands