background image

20

damage to the hob and constitutes incorrect installation, which is not 
covered by the warranty. 

Notes: 

   This could be a simple slot cut out of the plinth, or a dedicated 

ventilation grille. 

   The furniture top rail should not be fitted to the unit. This allows the 

induction hob to exhaust air into the kitchen space. 

  The recommended ventilation sizes are for guidance only.

If fitting a cooker hood above the hob:

If a cooker hood is to be installed above the hob, the height of 
the hood above the hob must be at least 600mm (650mm is 
recommended) (Fig. 4).  If the instructions supplied with the hood 
dictate that the hood must be installed at a height greater than 
600mm, then that height is the minimum required.

Wall furniture requirements:

The minimum height of any cabinet immediately above the hob is 
900mm.  The minimum height of any adjacent units (including light 
pelmets) is 400mm, unless they are manufactured from a material 
resistant to fire (steel, for example).

Notes:

   Do not position this appliance above a refrigeration unit.  The heat 

generated may cause the refrigeration unit to fail.

   This appliance is designed to be installed into cabinet units capable 

of withstanding temperatures of 65°C or greater above ambient 

Summary of Contents for hn6110





























Reviews: