background image

Gas Supply Requirements

IMPORTANT: THIS APPLIANCE SHOULD BE FITTED BY A GAS SAFE REGISTERED FITTER OR OTHER SUITABLY 
QUALIFIED PERSON.

  This installation must comply with the Gas Safety (installation and use) Regulations 1984.

  This appliance is category II2H3+ and is designed for use in the UK and Ireland. The installation must comply with the  

  Gas Safety (installation and use) Regulations 1984.

•  

The CDA Group Ltd is not legally able to provide any assistance in the installation of gas appliances except to Gas    

  Safe registered installers. Any Gas Safe registered fitter requiring help must provide their name, address and registration  
  number. Information supplied will be validated before help is provided.

 

•  

In the event that this appliance is not installed in accordance with the above requirements, the appliance may be  

 

•  

This appliance should be installed using 15mm copper pipe connected via a shut-off valve in an adjacent unit. The shut-off  

  valve needs to be accessible in an emergency or for service purposes. 

•  

This appliance must not be connected to a combustion gas recovery scavenging system

•  

The connection to the gas supply must comply with all current regulations in force.

•  

We are not legally able to offer advice on the installation of gas appliances to non Gas Safe registered personnel.

Ventilation

All rooms require a window or equivalent (e.g. a door) which can be opened. Some rooms require a permanent vent in 
addition to a window (see below).

This unit must not be used in a room which is less than 5m

3

. The following table details the requirements based on the 

kitchen volume (L x W x H) in m

3

.

The above requirements also allow use of a gas oven and grill but if there are any other fuel burning appliances in the 
same room, consult the relevant British Standard (BS5440) or Gas Safe document.

Room Volume (m

3

5

6 to 10

6 to 11

11 or more

Air Vent Required (cm

3

100

50

No permanent vent required if a door opens to the outside

None required

HCG601, HCG611, HCG621 Hob Manual.indd   8

5/6/09   13:04:18

disconnected from the mains gas supply until any faults are rectified; this is a legal requirement.

A kit is provided. Do not attempt to fit the conversion kit yourself.

•  

This appliance is suitable for conversion to Liquid Petroleum Gas (G30 or G31) or for natural gas (G20).  

Summary of Contents for HCG602













Reviews: