CDA HCC663 Manual For Installation, Use And Maintenance Download Page 5

5

Using your hob

To switch the zone on

•  

Touch the power key.

•  

Select the zone required by touching the zone selection key until the required zone flashes a 0 in the zone display.  

The order for zone selection is clockwise starting at the front right zone.

The zone display will flash for approximately ten seconds when the zone will be set at the power level selected or switch off if no 
power level is set.

Please note:

•  

To activate a zone, touch the zone selection key until the required zone display flashes.  When no display is  

 

 

flashing, the only control key that is active is the power on/off key.

To set the power level without Boost function

•  

Touch the – key to set the zone power level at 4, and then increase or reduce the power level using the + and –    

 

keys until the required level is set.

To set the power level with Boost function
The hob is equipped with a Boost function which will set the zone to its maximum power for a specific period of time, and then 
the zone will return to normal functioning.  

•  

Touch the + key to set the zone power level at 9 and then touch - to reduce the power level to the level  

 

 

required. The display will flash alternately an A and the power level.  After ten seconds, the zone will be set at  

 

 

the power level selected and the display will show an A.  

•  

To check on the power level selected, touch either the + or – key.    

Please note: 

•  

To switch off the boost function, it is necessary to reset the zone by completely switching it off and on again.

•  

As 9 is the maximum power level, there is no boost function available at power level 9.

To switch a zone off

•  

Select the zone required by touching the zone selection key until the required zone flashes a 0 in the  

 

 

zone display.

•  

Touch the + and – keys simultaneously for approximately three seconds.

To switch the hob off

•  

Touch the power on/off key for approximately three seconds.

Child lock
The hob is equipped with a childlock to prevent accidental use.  The child lock only operates when the hob is not in use.
 
To set the child lock

•  

Touch the power key.  

•  

Then touch the zone selection key and the - key simultaneously.  

•  

When the hob beeps, touch the + key.  The zone displays will show an L to confirm the child lock is set.

 
To switch off the childlock

•  

Touch the power key.  

•  

Then touch the zone selection key and the - key simultaneously.  

•  

When the hob beeps, touch the - key. 

Summary of Contents for HCC663













Reviews: