CDA dk1150 Series Manual For Installation, Use And Maintenance Download Page 16

16

Care and Maintenance

It is advisable to clean when the appliance is cold and especially for 

cleaning the enamelled parts.

Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on 

the surfaces.

Avoid using cleaning products with a chlorine or acidic base.

WARNING

When correctly installed, your product meets all safety requirements 

laid down for this type of product category. However special care 

should be taken around the rear or the underneath of the appliance 

as these areas are not designed or intended to be touched and may 

contain sharp or rough edges, that may cause injury.

Inside of Oven

The oven should always be cleaned after use when it has cooled down.

The cavity should be cleaned using a mild detergent solution and warm 

water.

Suitable proprietary chemical cleaners may be used after first consulting 

with the manufacturers recommendations and testing a small sample of 

the oven cavity. Abrasive cleaning agents or scouring pads/cloths should 

not be used on the cavity surface.

NOTE: 

The manufacturers of this appliance will accept no responsibility 

for damage caused by chemical or abrasive cleaning.

Enamelled Parts

All the enamelled parts must be cleaned with a sponge and soapy water 

only or other non-abrasive products.

Dry preferably with a micro fibre or soft cloth.

Stainless Steel, Aluminium, Painted Parts and Silk-

screen Printed Surfaces

Clean using an appropriate product. Always dry thoroughly.

Stainless steel surfaces: can be cleaned with an appropriate stainless steel 

cleaner.

IMPORTANT:

 these parts must be cleaned very carefully to avoid 

scratching and abrasion. You are advised to use a soft cloth and neutral 

soap.

Glass Control Panel

Clean using an appropriate product. Always dry thoroughly.

Do not use harsh abrasive cleaners or sharp metal scrapers to clean the 

control panel since they can scratch the surface, which may result in 

shattering of the glass.

ATTENTION:

Let the oven cool 

down and pay special 

attention no to touch 

the hot heating 

elements inside the 

oven cavity.

IMPORTANT:

Before any operation 

of cleaning and 

m a i n t e n a n c e 

disconnect the 

appliance from the 

electrical supply.

CAUTION:

Do not use harsh 

abrasive cleaners or 

sharp metal scrapers 

to clean the oven door 

glass since they can 

scratch the surface, 

which may result in 

shattering of the glass.

CAUTION:

Do not store 

flammable material

in the oven.

CAUTION:

Do not use a steam 

cleaner because the 

moisture can get into 

the appliance thus 

make it unsafe.

CAUTION:

Do not use abrasive 

substances or 

nonneutral detergents 

as these will 

irreparably damage 

the surface.

Summary of Contents for dk1150 Series

































Reviews: