CDA CVC11SS Manual For Installation, Use And Maintenance Download Page 12 | Manualshive

Page: 12 / 16

CDA CVC11SS Manual For Installation, Use And Maintenance Download Page 12

11

 

 

fig. 4

fig. 5

Installation

IMPORTANT: THIS APPLIANCE SHOULD BE FITTED BY SUITABLY
QUALIFIED PERSON.

1. Slide the base unit into the housing ensuring the dimensions are

correct as per figure 3.

2. Fix the base unit in place by attaching the 10 screws in to

the holes as shown in figure 4 and figure 5. If the sides of the

base are not flush with the sides of the housing, then use the

shims provided.

3. Push the runners fully closed on the base unit.
4. Connect the plug to the plug socket. This must be accessible

after the appliance has been installed.

5. Using an appropriate supply pipe, connect one end of the

hose to the threaded inlet of the valve on the dispenser, located

at the rear of the appliance.

6. Insert the flow restrictor between two rubber washers, then

connect the other end of the pipe to the mains water supply

(drinking water only)

7. Insert the appliance into the housing, ensuring that the runners

on the machine are located in the runners on the base unit.

Then slide the appliance fully into the housing.

Please note:
If the coffee machine is to be connected to the mains water supply
then it is not suitable for installation in a wall unit. The minimum
depth of the unit in this instance is approximately 400 mm
(dependent on the water connection pipe used).

320 min

320

542

fig. 3

«
...
10
11
12
13
14
...
»

Summary of Contents for CVC11SS

















Reviews:

No comments