CBS ArcSafe RSK-SACE2 User Manual Download Page 4

CBSArcSafe.com

 | 

Email: [email protected]

A Group CBS Company

CBS

Safe

®

Arc

5.  Turn the Power Switch on top the controller to the ON 

position.  The amber LED should illuminate indicating 
the unit is ready.

6.  When ready to operate actuator, press and hold the 

ENABLE button while depressing either the OFF or 
ON button for the desired operation.  Both buttons 
must be held depressed until the actuator has fully 
depressed the buttons.

7.  Release the ENABLE and OFF or ON buttons and the 

actuator will retract.

4.3 Actuator Mounting Bracket 

Use of the RSK-SACE2 Chicken Switch actuator will require 
the installation of a mounting bracket on the face of your 
breaker.  These brackets are attached to the breaker using 
industrial strength double sided adhesive manufactured 
by 3M.  Each breaker that the RSK-SACE2 is intended to be 
used on will require one of these brackets installed.  Each 
RSK-SACE2 comes with two mounting brackets.  Additional 
brackets can be purchased from MarTek by calling 1-800-
248-4958. Order Part Number P-0209.
Below is a picture of a bracket installed on the breaker.  
Detailed instructions for installing the bracket will be 
included with the bracket.

4.4 Actuator Mounting Bracket 

The slot on the bottom of the RSK-SACE2 actuator must be 
aligned over the mounting bracket.

STEP 1: 

Verify that both linear actuators are fully 

retracted into the actuator base.  Note that if the actuators 
are not fully retracted, you will not be able to install the 
actuator on the breaker. 

STEP 2: 

Align the RSK-SACE2 actuator slot over the 

bracket so that it engages the slots on the bracket. 

STEP 3: 

The RSK-SACE2 actuator should engage the 

mounting bracket and go flush against the breaker face. 

Summary of Contents for RSK-SACE2









Reviews: