Striker
face plate
Striker face
plate screws
11
11
. Position the striker face plate in the
centre of the striker body - this may need to
be adjusted in the steps following. Insert the
striker face plate screws and loosely tighten.
12
. Close the door. When the striker is fitted
correctly the magnet will draw the plunger
forward. If this does not happen the striker is
misaligned with the plunger (see below).
If the alignment is correct, tighten the screws
and skip to Step 14; otherwise continue to
Step 13.
✗
✗
✓
12
13
Striker
face
plate
screws
2.5mm
(3/32”)
2.5mm
(3/32”)
Striker
Plunger
13
. The striker allows 2.5mm (3/32”) of
adjustment in each direction when the
striker face plate is fitted in the centre of
the striker body.
To adjust the face plate position, loosen the
striker face plate screws slightly and adjust
the face plate up or down to allow the
Plunger
flats
14
. Manually push the plunger forward until
there is no gap between spring reservoir one
(SR1) and spring reservoir two (SR2).
Restrain the plunger nut using the large end
of one of the two identical supplied spanners.
Push
here
➟
14
Turn
clockwise
15
15
. Place the small end of the second spanner
across the flats under the head of the plunger.
Keep the spanner restraining the plunger nut
stationary while turning the second spanner
clockwise.
Continue to turn the spanner until there is no
longer a gap between the spanner and the
chassis.
Now turn the spanner anti clockwise half a turn.
The plunger should now be adjusted correctly.
Slide the door closed to check.
Adjust if necessary.
Gap
No
gap
16
. Fit the remaining side handle (with
visible handle joining screws fitted) to
the chassis by sliding the front flange of
the handle under the heads of the 3x side
handle to chassis screws.
Tighten the screws.
16
18
. Fit the passage face plate to the chassis
using the 3x face plate screws.
17
. Use the ball end of the CL400 Allen key to
tighten the 2x handle joining screws.
Use the other end of the Allen key to firmly
tighten the screws.
8
8
. Remove the striker from its box. Remove
the striker face plate from the striker body.
Insert the 2x striker nuts into the recess in the
back of the striker body.
Insert the 2x striker face plate screws through
the slot in the front face of the striker body
and into the striker nuts. Loosely tighten the
screws.
Striker nuts
Striker
nuts
Rear View
Striker
body
7
. Open the door. Transfer the horizontal line
across the centre of the closing jamb. This
line represents the top of the striker cut out.
A double-sided striker cut out template
has been provided. Use the ‘FLUSH striker
template’ and instructions to router out the
recess in the closing jamb.
32 40
32 40
40 32
40 32
2
3
7
CL
5
4
6
Horizontal
line
Striker
template
Centre of
closing jamb/
centre of
door closing
position
CL
7
Striker
body
Striker face
plate screws
Striker
mounting
wood
screws
9
Striker face plate
screws
9
. Insert the striker body, with the striker
face plate screws and the striker nuts
attached, into the cut out in the closing
jamb.
Striker
face
plate
screws
10
10
. Remove the striker face plate screws.
The striker nuts are now trapped in position.
5
7
6
PAGE
PAGE
PAGE
Front
flange
Face
plate
screws
Passage
face plate
© Cavity Sliders Limited. CAVILOCK
®
CL400
®
MAGNETIC (O.D. 2013) ADA PASSAGE INSTRUCTIONS.
61229/CL405ZA920 - 02.2018
All copyright and other property in this document is reserved by Cavity Sliders Limited. Details and specifications are subject to
change without notice. Whilst all care is taken to ensure the accuracy of all information, no responsibility will be accepted for any
errors or omissions. ® CS FOR DOORS, CS CAVITY SLIDERS and CAVILOCK are Registered Trademarks. Patents pending.
18
17
19
. If you are installing a CL400 Bi-Parting -
Passage (Non Latching) handle, both handles
are the same and you can simply repeat the
Passage Handle installation instructions for the
second door.
Ignore any reference to the striker or plunger.
8
PAGE
Fitting the Remaining Side Handle
Adjusting the Plunger
Fitting the Face Plate
Bi-Parting Handles
Adjusting the Plunger
Screw the 4x striker mounting wood screws
into the closing jamb.
Spanner
Spanner
Plunger
nut
Plunger
plunger to penetrate the striker face plate. If
the plunger still fails to penetrate the striker face
plate, the door height may need to be adjusted.
Fitting the Striker
Fitting the Striker
Cavity Sliders Limited
Auckland Head Office
5 - 7 Rakino Way
Mt Wellington
Auckland, NZ
T +64 9 276 0800
F +64 9 276 2525
[email protected]
Recyclable
Packaging
www.csfordoors.co.nz
www.cavitysliders.com.au
www.cavitysliders.com
SR1 SR2
No gap
CL400
Allen key
M3.5
handle
joining
screws
M3.5
handle
joining
screws
