2
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MENU
MENU
Starting/Stopping measurement
You can select the Auto mode (automatic mea-
suring) or manual mode. During measurement,
km/h or mph flashes. The maximum speed and
total distance are updated regardless of start-
ing/stopping measurement.
Auto mode (
•
on)
Measurements start automatically when the
bicycle is in motion.
Manual mode
•
When the computer is mounted on the
bracket, start/stop measuring by pressing
the MODE and SSE buttons simultaneously.
For switching between Auto and Manual mode, refer
*
to “Auto mode setting” on the menu screen.
Switching computer function
Pressing the MODE changes the middle/bottom row display.
Sea level altitude correction
Shortcut A
: MODE (By pressing & holding)
→
Back to the previous measuring screen
...................................Select ADJUST (sea level altitude correction) or HOME (home altitude
setting) by pressing MODE. When MODE and SSE are pressed simul-
taneously,“+/- selection” or “Move digit” can be selected, and pressing
MODE increases the +/- selection or the value. Enter the desired altitude.
For details, refer to “Sea level altitude correction”.
*
Countdown distance setting
Shortcut B
: MODE (By pressing & holding)
→
Back to the previous measuring screen
................................Pressing MODE increases the value and pressing MODE and SSE
simultaneously moves to the next digit.
Wheel selection .....Toggle between the specified wheel size (tire circumference)
and
. Use this function if the computer is to be shared between
two bicycles. Pressing MODE toggles between
and
.
Wheel size entry ....Pressing MODE increases the value and pressing MODE and SSE
simultaneously moves to the next digit. To enter the wheel size
,
display
using “Wheel selection”.
Auto mode setting ...Press MODE to select ON or OFF.
Clock setting ...........Operate as described in “Preparing the computer 5”.
Total distance manual entry
................................Before re-initializing the computer, note the total distance. This
reading will later allow you to enter the total distance manually.
Pressing MODE increases the value and pressing MODE and SSE
simultaneously moves to the next digit.
Sensor ID setting ....Pressing MODE changes to ID1 or ID2, and pressing MODE and
SSE simultaneously moves to ID setting. Set the ID as described
in “Preparing the computer 4”.
ID2
*
is used when the computer is shared with the second sensor installed
to another bicycle. The computer will identify ID1 and ID2 automatically
after waking up from Power-saving mode.
Speed/temperature unit selection
................................Operate as described in “Preparing the computer 2”.
Changing the computer settings [Menu screen]
Pressing MENU on the measuring screen moves to the menu screen for setup change. Once in-
side the menu screen, press the MODE button to scroll through setup items. Press MODE+SSE to
enter the edit screens. Change cannot be done if there is an incoming signal and timer is active.
Shortcut
: When using a shortcut, the sea level altitude correction screen or the countdown distance setting
screen is not displayed as shown in the figure below. It moves directly to the edit screen.
Resetting data
While displaying any data other than Dst-2, pressing and holding the MODE and SSE
simultaneously resets the measurement data to 0. While displaying Dst-2, pressing and
holding the MODE and SSE simultaneously resets only Dst-2 to 0. In both cases, the
total distance and total altitude gain are not reset.
Power-saving mode
If the computer has not received a signal for 10 minutes, power-saving mode will activate and
only the clock will be displayed. When the computer receives a sensor signal again, the mea-
suring screen reappears. If 60 minutes’ inactivity elapses, power-saving mode will change to
SLEEP mode. Pressing the MODE in SLEEP mode brings up the measuring screen.
Altitude measurement
This unit detects the change in atmospheric pressure and temperature using a pressure sensor
built in the computer, and converts it to the altitude using the relation between the altitude and
pressure of ISO 2533 (Standard atmosphere), which was developed based on the international
standard atmosphere specified by the International Civil Aviation Organization (ICAO). Accord-
ingly, the measurements tend to change, even at the same point, according to the atmospheric
pressure due to the weather condition. Furthermore, the measurements may change more
than 30 m from the early morning to the evening even under a stabilized weather condition.
The measurements may be incorrect in the following place or environment.
When the atmospheric pressure and temperature change significantly due to a rapid
•
weather change.
In the place where the atmospheric pressure is regulated, such as inside an airplane.
•
The altitude data may change temporarily when the temperature changes rapidly by get-
•
ting out of a room, etc. It may return to a correct value after a while.
Altitude measurement
This unit has four altitude-related functions and temperature function.
Sea level altitude ....The current sea level altitude is displayed.
For effective use of the sea level altitude, refer to “Sea level altitude correction”.
*
Slope ......................Measures slope in percent unit, where 45 degree angle being 100%.
It is updated every 3 seconds, calculating from several times of the change in
*
altitude and the trip distance. Slope update may be delayed. Abnormal data may
also be temporarily displayed when speed quickly changes or during low-speed.
Ascending altitude ...Accumulation of ascent from the reset point to the current point is displayed.
Total altitude gain ...The total altitude gain is displayed.
Operating the computer [Measuring screen]
Temperature ...........The current temperature is displayed.
It is updated when the measurement screen is displayed (while measuring:
*
every 3 seconds, while not riding: every 20 seconds).
The altitude measurement is updated every 3 seconds during measurement (when counting the
*
elapsed time), but not updated when measurement stops.
Caution:
When Auto mode is Off, elapsed time counts even if the bicycle is not in motion.
After measurement, be sure to press MODE and SSE simultaneously to stop measuring.
Sea level altitude correction
This unit determines the altitude by converting the change in atmospheric pressure and tem-
perature; therefore, it may cause deviation from the actual sea level altitude. It is recommended
to correct the sea level altitude just before measurement, using either the following methods.
• ADJUST (sea level altitude correction): Enter the altitude at the current point.
Enter the actual value at the point where the sea level altitude is known,
such as along the seashore, or at a sign on the mountain, etc.
Press and hold
*
MODE and SSE simultaneously on the setting screen to reset the cor-
rected value to the default (a value according to ISO2533).
• HOME (home altitude setting): Preset a specific sea level altitude.
Preset the sea level altitude at your home in advance. Move to the HOME screen,
and then return to the measuring screen by pressing MENU or the relevant short-
cut. Then, the sea level altitude changes to the preset value. You can start with the
correct sea level altitude by setting home altitude before stating from your home.
The sea level altitude is corrected on the menu screen “Sea level altitude correction”. Move to the sea
*
level altitude correction screen by pressing MENU or the relevant shortcut from the measuring screen.
Countdown distance
Once the target trip distance is set, the unit displays the countdown distance to the target,
and notifies at arrival. When the unit reaches the target distance, the countdown distance
appears and the value flashes. The screen returns to the original display in 5 seconds.
The target distance is set on the menu screen “Countdown distance setting”. Move to the countdown
*
distance setting screen by pressing MENU, MODE, or the relevant shortcut from the measuring screen.
: Pace arrow
Indicates whether the current speed is
faster ( ) or slower ( ) than the average
speed.
: Auto mode icon
: Low battery indicator of the computer
Current speed
0.0(4.0) – 105.9 km/h
[0.0(3.0) – 65.0 mph]
Selected mode at
the bottom
Selected mode at
the middle display
With the computer installed on the bracket, press on the four raised dots on the face of the computer.
*1
If
*2 Tm exceeds approximately 27 hours or Dst exceeds 9999.99 km, .E (Error) is displayed as the
average speed. Reset data.
After changing, be sure to press
*
MENU to register the setting.
If the setting screen is not touched for a minute, the measur-
*
ing screen appears without data changes.
Setting change
( b y p r e s s i n g
simultaneously)
MODE+SSE
MODE+SSE
Tm
Elapsed Time
0:00’00” – 99:59’59”
Bottom display
Dst
Trip Distance
0.00 – 9999.99 km [mile]
Dst
2
Trip Distance-2
0.00 – 9999.99 km [mile]
Av
Average Speed
*2
0.0 – 105.9 km/h [0.0 – 65.0 mph]
Mx
Maximum Speed
0.0(4.0) – 105.9 km/h [0.0(3.0) – 65.0 mph]
Countdown
Distance
9999.90 – 0.00 km [mile]
Odo
Total Distance
0.0 – 9999.9 / 10000 – 999999 km [mile]
Clock
0:00 – 23:59 or 1:00 – 12:59
Sea Level Altitude
Ascending
Altitude
0 – 999999 m [ft]
Total Altitude
Gain
0 – 99999
/ 100 – 99999 x 1000 m [ft]
Temperature
-20 – 60 ˚C
[-4 – 140 ˚F]
-500 – 9000 m
[-1640 – 29600 ft]
-99% – +99%
Slope (%)
Middle display
Sea level alti-
tude correction
Countdown distance setting
Wheel selection
Wheel size entry
Auto mode setting
Clock setting
Total distance manual entry
Sensor ID setting
Speed/temperature unit selection
Measuring screen
Menu
screen
MODE
MODE
*1
(By pressing
& holding)
MODE
MODE
Shortcut A
(By pressing
& holding)
MODE
MODE
Shortcut B
Shortcut to sea level
altitude correction.
Valid while the com-
puter is receiving no
signal from sensor.
Shortcut to countdown distance setting. Valid while
the computer is receiving no signal from sensor.
