background image

- 2 - 

 

Safety precautions 

In order to ensure your safety, please read the following note   

1.

 

Before using this product, please read it before using it. Study and understand the 

instructions and all warning labels (it is recommended to be familiar with the normal 

operation  and  use  of  the  device  before  using  this  product.  Relevant  information  is 

available in this specification and local retailers)   

2.

 

Please  keep  this  specification,  and  ensure  that  all  warning  labels  are  clear  and 

complete .   

3.

 

This product recommends that more than two people install. 

4.

 

Please consult your doctor for advice   

5.

 

Before you start exercising. Please ensure safety when children are present.   

6.

 

Be careful when you have children who use them off the court. 

7.

 

  Please  check  the  wire  rope  regularly  If  there  are  any  signs  of  wear  and  tear  that 

may cause a certain risk to you, please maintain the extensibility of your hands, limbs 

and clothes so that you can fully and safely use this instrument . 

8.

 

Please pay attention to any possible signs of machinery, including wear and tear of 

parts, loosening of hardware and welding cracks. If any of the above signs are found, 

stop using this device immediately and contact our after-sales service department . 

9.

 

You can use the wrench inner hexagonal wrench to complete the assembly . 

10.

 

Maximum training load of this instrument: 120KG is limited to 100 KGbody use . 

11.

 

The  final  interpretation  of  the  company  is  owned  by  the  company,  subject  to 

change without prior notice 

 

Summary of Contents for GB17498.1















Reviews: