background image

SERVICE MANUAL

67102 PLUNGER PUMP

SERVICING THE 67102 PLUNGER PUMP SERIES

Do not service pump or electrical equipment while energized. 
Electricity can cause personal injury, death or property damage.

1.  Adhere to “Lock Out” and “Tag Out” procedures for electrical equipment.
2.  Before commencing pump service, turn power supply off. 
3.  Keep water away from electrical outlets and electrical devices.
4.  Electrical components must be installed by a qualified 

electrician to avoid risk of electrocution.

IMPORTANT SAFETY INSTRUCTIONS

It is the responsibility of the user to read and understand all instructions, important safeguards, and safety precautions before operating or 
servicing any pump. Failure to do so may result in property damage, personal injury or death.

General Safety Information and Symbols

Pay special attention to the following signal words, safety alert symbols and statements:

indicates a hazardous situation which, if not avoided, will result in death or serious injury.

indicates a hazardous situation which, if not avoided, could result in death or serious injury.

indicates a hazardous situation which, if not avoided, could result in minor or moderate injury or property damage.

indicates a hazardous situation which, if not avoided, could result in property damage.

Indicates a potential personal injury hazard. Obey all safety messages that follow this symbol to avoid possible injury or death.

WARNING

WARNING

CAUTION

NOTICE

DANGER

 

PUMP 

MODEL

FLOW

PRESSURE

RPM

TEMPERATURE

SHAFT DIA.

OIL CAPACITY

gpm

lpm

psi

bar

Pump

Motor

˚F

˚C

in

mm

oz

l

67102

100.0

378.5

1,000

69

680

140

60

1.772

45

320

9.46

67102C

100.0

378.5

1,000

69

680

140

60

1.772

45

320

9.46

Summary of Contents for 67102

















Reviews: