background image

1

[email protected]

If you have any questions or comments about this product, please contact us 

at

Always read and follow the instructions before use.

When assembling and using this product, basic safety precautions must always be 

followed to reduce the risk of personal injury and damage to the product or surroundings. 

Be sure to keep all children and pets away from the assembly area.

Do not attempt to assemble the gazebo in windy or wet conditions.  

Do not place your gazebo in an area exposed to excessive wind.  

Some parts contain sharp edges. Wear protective gloves when handling these items.  

It is recommended that, for safety issues, 2-4 people assemble the gazebo.  

You must schedule enough time to complete the assembly. You can not leave the unit 

unattended if it is not fully assembled, even if it is already anchored to the ground.

You should begin the assembly no less than 2m from any fixed obstruction such as 

fences, a garage, a house, overhanging branches, electrical wires, or laundry lines.

You must assemble your unit on level ground or platform. The unit must be anchored to 

either wood, stone tiles, or concrete using appropriate screws for that flooring, or 

anchored into the earth or grass with proper camp nails or anchors. Failure to do so may 

risk blowing away by the wind.

Check that all screws are tight before and during usage.

Do not place any type of heat conductor under or within 1.5m of, the unit including, but 

not limited to a barbecue or space heater.

Your gazebo has been created as a non-permanent structure. It is designed for leisure 

use and is not a shelter against adverse weather conditions. Do not use this gazebo in 

storms, hurricanes, typhoons, strong wind. Please remove the roof canopy at least 

before the extreme weather.

The roof will not resist cold and heavy and/or continuous snow accumulation. The frame 

may be left up year-round however you MUST remove the roof canopy during snowing 

winter.  

The unit must always remain anchored properly to the floor or ground using the 

appropriate screws to enjoy safe usage of the gazebo.

2-4 people to assemble recommended.

Proper tools: Two ladders, Allen wrenches, Power tools, Gloves, Spirit Level.

Do not destroy boxes until completely assembled.  

Do not tighten bolts immediately. Be careful power tools may over-tighten fittings. 

Tight bolts after completely set up.  

Always be patient, understand each step and get the parts ready before assembling.

Assembly tips

Summary of Contents for Thorncrest 3338453













Reviews: