manualshive.com logo in svg

CASTLE TSM-21, Diagnostic Manual

Share
Download
CASTLE TSM-21 Diagnostic Manual Download Page 13

 

 

Castle Inc 

TSM-21 Diagnostic Manual v2 

Page 13 of 63 

 

4.3  Drill Operation 

 

Page Procedure

 

Drill

 DOES NOT come out, Machine Routs, Clamp DOES NOT release: 

□

 Check Drill Solenoid for function or blockage…………………….. 

40-41 

21.51 

□

 Unclog Drill Solenoid…………………………………………………

38-39 

21.50 

 

Drill

 comes out and stays out as soon as air is attached…with Machine power OFF: 

Machine DOES NOT finish cycle when carriage is pushed forward by hand: 

□

 Check Drill Motor is On……………………………………………… 

33-34 

21.40 

□

 Check Drill Stop Switch for function or adjustment………………. 

37-38 

21.43 

 

Drill

 comes out and stops,  Router cuts pocket and Clamp DOES NOT release: 

Machine DOES finish cycle when carriage is pushed forward by hand: 

□

 Adjust Air pressure, may be too low………………………………..

51-52 

21.90 

□

 Check Drill Solenoid for function or blockage …………………….. 

40-41 

21.51 

□

 Unclog Drill Solenoid…………………………………………………

28-39 

21.50 

□

 Check Router SQE Valve……………………………………………

   (or Solenoid exhaust port ) for leakage 

43-44 

21.61 

□

 Check Drill SQE Valve……………………………………………….

   (or Solenoid exhaust port ) for leakage 

43-44 

21.61 

 

Drill

 bit not completing pilot hole into Pocket: 

□

 Adjust air pressure, Machine cycling too slowly………………….. 

51-52 

21.90 

□

 Bit mounted too deep into collet…………………………………….

34-35 

21.41 

 

Drill

 bit separating from the shank: 

□

 Adjust air pressure, Machine cycling too slowly………………….. 

51-52 

21.90 

□

 Bit mounted too deep into collet…………………………………….

34-35 

21.41 

Summary of Contents for TSM-21
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands