Casio QW 5535 Operation Manual Download Page 5

Operation Guide 5535

E-49

2.  Press 

C

 to change the selection in the following sequence.

Hour and minute

DST

C

3.  Press 

D

 to increase the selected digits and 

B

 to decrease them.

 

x

 Each press of 

D

 toggles summer time between on (ON) and off (OFF). When 

summer time is on, a DST indicator is displayed on the Dual Time Mode screen.

 

x

 While the 12-hour format is selected for timekeeping, a 

P

 (PM) indicator will 

appear for times from noon to 11:59 p.m. 

4.  After you set the time, press 

A

 to return to the Dual Time Mode.

 

x

 In the Dual Time Mode, the seconds count is synchronized with the seconds 
count of the Timekeeping Mode.

Note

 

x

 Daylight Saving Time (summer time) advances the time setting by one hour from 
Standard Time. Remember that not all countries or even local areas use Daylight 
Saving Time.

E-48

 Dual Time Mode

You can use the Dual Time Mode to set a second time (in 
15 minute steps) that is different from the Timekeeping 
Mode time.

To enter the Dual Time Mode

Use 

C

 to select the Dual Time Mode as shown on 

page E-11.

To set the Dual Time

1.  Hold down 

A

 while in the Dual Time Mode. The hour 

and minute digits flash on the display because they 
are 

selected

.

Current time

Minutes

Hour

E-47

 Alarm indicator

 Alarm on/off

 Hourly time signal indicator

To stop the alarm

Press any button.

E-46

 To turn an alarm and the Hourly Time Signal on or off

1.  In the Alarm Mode, use 

D

 or 

B

 to select an alarm or the Hourly Time Signal.

 

x

 Each press of 

D

 or 

B

 cycles between the alarm time screen and the hourly 

time signal setting screen.

2.  Press 

A

 to toggle the displayed setting (alarm or hourly time signal) between 

on and off.

 

x

 This will cause the second hand to move to 

ON

 or 

OFF

.

 

x

 An alarm on indicator will be on the display whenever any one of the five alarms 
is turned on. Turning on the hourly time signal causes its indicator to appear on 
the screen.

E-45

3.  Press 

C

 to move the flashing between the hour and 

minute settings.

4.  While a setting is flashing, use 

D

 (+) and 

B

 (–) to 

change it.

 

x

 While the 12-hour format is selected for timekeeping, 

P

 (PM) indicator will appear for times from noon to 

11:59 p.m. 

5.  Press 

A

 to exit the setting mode.

To test the alarm

In the Alarm Mode, hold down 

D

 to sound the alarm.

Alarm time hour

E-44

 To set an alarm time

1.  Press 

D

 or 

B

 to display the setting (

–1

 through 

–5

, or 

SIG

) you want to 

change.

–1

–2

–5

–3

–4

D

B
B

D

D

B
B

D

D

B

B

D

SIG

2.  Hold down 

A

 until the hour digits of the current alarm time start to flash (about 

two seconds). This is the setting mode.

 

x

This also causes the alarm indicator to appear and turns on the alarm setting.

E-43

 Using the Alarm

You can set up to five different alarms.
The watch beeps for about 10 seconds when the alarm 
time is reached. The hourly time signal causes the watch 
to beep every hour on the hour.

To enter the Alarm Mode

Use 

C

 to select the Alarm Mode as shown on page E-11.

E-42

 To perform a countdown timer operation

D

D

D

D

B

Start

Stop

(Resume)

(Stop)

Reset

 

x

 Before starting a countdown timer operation, check to make sure that a 
countdown operation is not in progress (indicated by the seconds counting down). 
If it is, press 

D

 to stop it and then 

B

 to reset to the countdown start time.

To stop the alarm

Press any button.

E-41

To configure the countdown timer

1.  Hold down 

A

 for about two seconds until the minute 

digits of the start time start to flash.

 

x

 If the countdown start time is not displayed, use the 
procedure under “To perform a countdown timer 
operation” (page E-42) to display it.

2.  Press 

C

 to toggle the flashing between the minutes 

and seconds.

3.  Use 

D

 and 

B

 to change the setting of the flashing digits (minutes or seconds).

 

x

 You can set a start time in the range of one second to 100 minutes in 
one-second increments.

 

x

 To set the starting value of the countdown time to 100 minutes, set 00'00.

4.  Press 

A

 to exit the setting mode.

E-40

 Countdown Timer

The countdown timer can be set within a range of 
one second to 100 minutes. An alarm sounds when the 
countdown reaches zero.

To enter the Countdown Timer Mode

Use 

C

 to select the Countdown Timer Mode as shown 

on page E-11.

Seconds

Minutes

Summary of Contents for QW 5535








Reviews: