— 3 —
Module 3750
Module 4314
DST indicator
City code
Current time for
the selected
city code
Module 3750
Module 4314
World Time
World Time digitally displays the current time in 27 cities
(29 time zones) around the world.
•
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing
C
.
To view the time in another city
In the World Time Mode, press
D
to scroll eastwardly
through city codes.
•
For full information about city codes, see the “City Code
Table”.
•
If the current time shown for a city is wrong, it probably
means there is a problem with your Timekeeping Mode
time and/or Home City code settings. Go to the
Timekeeping Mode and make the necessary
adjustments.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use
D
to display the city code
whose Standard Time/Daylight Saving Time setting you
want to change.
2. Hold down
A
for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
•
The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
•
Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
•
Note that you cannot switch between Standard Time
and Daylight Saving Time while
GMT
is selected as the
city code.
Seconds
Minutes
Module 3750
Module 4314
Countdown Timer
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
•
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C
.
Configuring the Countdown Timer
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
•
See “To configure the countdown timer” for information
about setting up the timer.
Auto-repeat
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is repeated
a total of eight times, after which it stops automatically.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
•
Pressing
D
while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing
D
, or you can
press
A
to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
•
When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
•
When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
•
Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
•
30 seconds before the end of the countdown, the watch emits four short beeps.
•
The watch emits a short beep for each of the last 10 seconds of the countdown.
•
If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down
A
until the current
countdown start time starts to flash, which indicates the
setting screen.
•
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press
C
to move the flashing in the sequence shown
below to select other settings.
Start Time
Auto-repeat
Progress Beeper
Setting
Start Time
Auto-repeat
Progress Beeper
Screen
Button Operation
Use
D
(+) and
B
(–) to change the setting.
•
You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
Press
D
to toggle auto-repeat on (
displayed) and off
(
displayed).
Press
D
to toggle the progress beeper on (
ON
) and off
(
OF
).
3. When the setting you want to change is flashing, use
B
and
D
to change it as
described below.
4. Press
A
to exit the setting screen.
•
You can also perform steps 1 and 2 of the above procedure whenever you need to
view the current auto-repeat and progress beeper settings.
To use the countdown timer
Press
D
while in the Countdown Timer Mode to start the
countdown timer.
•
The countdown timer operation continues even if you
exit the Countdown Timer Mode.
•
Press
D
while a countdown operation is in progress to
pause it. Press
D
again to resume the countdown.
•
To completely stop a countdown operation, first pause it
(by pressing
D
), and then press
A
. This returns the
countdown tme to its starting value.
Minutes
Seconds
1/100
second
Module 3750
Module 4314
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
•
The display range of the stopwatch is 59 minutes,
59.99 seconds.
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
C
.
To measure times with the stopwatch
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Start
Split
Split release
Stop
Clear
Start
Split
Stop
Split release
Clear
Split Time
Two Finishes
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Alarm
number
Alarm time (Hour : Minutes)
On/Off status
Module 3750
Module 4314
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
•
There are six screens in the Alarm Mode. Four are for
one-time alarms (indicated by numbers from
AL1
through
AL4
), one is for a snooze alarm
(indicated by
SNZ
), and one is for the Hourly Time
Signal (indicated by
SIG
).
•
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
C
.
To set an alarm time
1. In the Alarm Mode, use
D
to scroll through the alarm
screens until the one whose time you want to set is
displayed.
•
To set a one-time alarm, display one of the screens indicated by an alarm number
from
AL1
through
AL4
. To set the snooze alarm, display the screen indicated
by
SNZ
.
•
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down
A
until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
•
This operation automatically turns on the alarm.
3. Press
C
to move the flashing between the hour and minute settings.
4. While a setting is flashing, use
D
(+) and
B
(–) to change it.
•
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press
A
to exit the setting screen.