2
Operation Guide 3085
DST indicator
Current time in the zone
of the selected city code
City code
World Time
World Time shows the current time in 48 cities (29 time
zones) around the world.
•
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing
C
.
To view the time for another city code
In the World Time Mode, press
D
to scroll eastwardly
through city codes.
•
For full information about city codes, see the “City Code
Table”.
•
If the current time shown for a city is wrong, check your
Timekeeping Mode time and Home City code settings
and make the necessary changes.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use
D
to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down
A
for about one second to toggle between
Daylight Saving Time (
DST
indicator displayed) and
Standard Time (
DST
indicator not displayed).
•
The
DST
indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
•
Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
•
In the World Time Mode, you can switch the city code
you currently have selected as your Timekeeping Mode
Home City between Standard Time and DST. The
setting you select in the World Time Mode will also be
applied in the Timekeeping Mode.
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
•
There are six screens in the Alarm Mode. Five are for
alarms (indicated by numbers from
through
), and one is for the Hourly Time Signal (indicated
by
).
•
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
C
.
•
You can select any one of three alarm beeper patterns.
Alarm number
On/Off status
Alarm time
(Hour : Minutes)
To set an alarm time
1. In the Alarm Mode, use
D
to scroll through the alarm
screens until the one whose time you want to set is
displayed.
•
To set an alarm, display one of the screens indicated by an alarm number from
through
.
2. After you select an alarm, hold down
A
until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
•
This operation turns on the alarm automatically.
3. Press
C
to move the flashing between the hour and minute settings.
4. While a setting is flashing, use
D
(+) and
B
(–) to change it.
•
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (
P
indicator).
5. Press
A
to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
•
To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down
D
to sound the alarm.
•
The alarm will sound using the currently selected beeper pattern.
To turn an alarm on and off
1. In the Alarm Mode, use
D
to select an alarm.
2. Press
A
to toggle it on (
displayed) and off
(
displayed).
•
Turning on an alarm (
through
) displays the
alarm on indicator on its Alarm Mode screen.
•
In all modes besides the Alarm Mode, the alarm on
indicator is shown for any alarm that is currently turned
on.
•
The alarm on indicator flashes while the alarm is
sounding.
Alarm on indicator
On/Off status
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use
D
to select the Hourly Time
Signal (
).
2. Press
A
to toggle it on (
displayed) and off
(
displayed).
•
Turning on the Hourly Time Signal displays the Hourly
Time Signal indicator on its Alarm Mode screen.
•
While the Hourly Time Signal is turned on, the Hourly
Time Signal on indicator is shown on the display in all
modes besides the Alarm Mode.
Hourly time signal
on indicator
On/Off status
1/100 second
Minutes
Seconds
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
•
The display range of the stopwatch is 59 minutes,
59.99 seconds.
•
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
C
.
Seconds
Hours
Minutes
To measure times with the stopwatch
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Start
Split
( displayed)
Split release
Stop
Clear
Start
Split
Stop
Split release
Clear
Split Time
Two Finishes
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Countdown Timer
You can set the countdown timer within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
•
You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
•
All of the operations is this section are performed in the
Countdown Timer Mode, which you can enter using
C
.
To use the countdown timer
Press
D
while in the Countdown Timer Mode to start the countdown timer.
•
When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
•
When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds to signal when the countdown
reaches zero.
•
The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
•
Press
D
while a countdown operation is in progress to pause it. Press
D
again to
resume the countdown.
•
To completely stop a countdown operation, first pause it (by pressing
D
), and then
press
A
. This returns the countdown time to its starting value.
To set up the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down
A
until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
•
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press
C
to move the flashing in the sequence shown
below to select other settings.
Auto-repeat
Minutes
Hours
3. While a setting is flashing, use
D
and
B
to change it as described below.
Screen
Do this:
Use
D
(+) and
B
(–).
Press
D
.
To do this:
Change the hours or minutes
Toggle auto-repeat on (
) and off (
)
•
To specify a countdown start time of 24 hours, set
.
4. Press
A
to exit the setting screen.
•
The auto-repeat on indicator (
) is displayed on the Countdown Timer Mode
screen while this function is turned on.
•
Frequent use of auto-repeat and the alarm can run down battery power.