Operation Guide 5208
E-20
Alarms
The Alarm Mode lets you configure five daily alarms. You
also can use it to turn the Hourly Time Signal on or off.
•
The watch beeps for about 10 seconds when an alarm
time is reached.
•
Turning on the Hourly Time Signal causes the watch to
beep on the hour every hour.
•
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
C
(page
E-9).
Alarm time
(Hour : Minutes)
E-21
To set an alarm time
1. In the Alarm Mode, use
D
to scroll through the alarm screens until the one whose
time you want to set is displayed.
AL1
AL2
AL3
SIG
AL5
AL4
•
The alarm screens are
AL1
,
AL2
,
AL3
,
AL4
, and
AL5
.
About 2 seconds
Alarm time
Alarm number
▲
▲
E-22
2. After you select an alarm, hold down
A
for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
•
This operation turns on the alarm automatically.
3. Press
C
to move the flashing between the hour and minute settings.
4. While a setting is flashing, use
D
(+) and
B
(–) to change it.
5. Press
A
to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in.
•
Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
•
To stop the alarm tone after it starts to sound, press any button.
E-23
To turn an alarm on and off
1. In the Alarm Mode, use
D
to select an alarm.
2. Press
A
to toggle it on and off.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use
D
to select the Hourly Time
Signal (
SIG
) (page E-21).
2. Press
A
to toggle it on and off.
Hourly time signal
on indicator
Alarm on indicator
E-24
Countdown Timer
Seconds
Minutes
Timer 1
Dual timers can be set with two different starting times. The watch can be configured
so the two timers alternate, so when one reaches the end of its countdown, the other
timer starts. You can specify a “number of repeats” value from 1 (once) to 10 (ten
times), which controls how many times the two-timer countdown operation is
performed. The starting time of each timer can be set in five-second steps up to 99
minutes, 55 seconds.
A
▲
▲
2 seconds
Seconds
Minutes
Timer 2
E-25
The watch emits a short beep whenever either of the timers reaches the end of its
countdown during an ongoing timer operation. The watch emits a 5-second beep
when the end of the final timer operation (specified by the number of repeats) is
reached.
•
All of the operations in this section are performed in the Countdown Timer Mode,
which you enter by pressing
C
(page E-9).
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero. The
beeper stops after about 5 seconds or when you press any button.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down
A
until the current
countdown start time starts to flash, which indicates the
setting screen.
•
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-27) to display it.
E-26
•
To disable either timer, set 00'00" as its countdown start time.
4. Press
A
to exit the setting screen.
Button Operation
Use
D
(+) and
B
(–) to change the setting.
Use
D
(+) and
B
(–) to change the setting.
Setting
Minutes, Seconds
Number of Repeats
Screen
2. Press
C
to move the flashing in the sequence shown below to select other
settings.
Timer 1
Minutes
Timer 1
Seconds
Timer 2
Seconds
Timer 2
Minutes
Number of Repeats
3. When the setting you want to change is flashing, use
D
and
B
to change it as
described below.
E-27
To use the countdown timer
Press
D
while in the Countdown Timer Mode to start the countdown timer.
•
Pressing
A
while a countdown is in progress will display the repeat count (current
repeat count/preset number of repeats). The ongoing countdown will reappear
automatically after about two seconds.
•
The countdown is performed by alternating between Timer 1 and Timer 2. A short
beep is emitted to signal a changeover from one timer to the other.
•
Pressing
A
while a countdown timer is stopped resets that time to the start time specified
by you.
•
Press
D
to pause a countdown. Press
D
again to resume.
•
The watch emits a 5-second beep when the end of the final timer operation
(specified by the number of repeats) is reached.
Current timer time
Preset number of repeats
Current repeat count
Timer (1 or 2)
(Reset)
(Start/Stop)
A
▲
▲
2 seconds
E-28
•
Even if you exit the Countdown Timer Mode, the countdown timer operation
continues and the watch beeps as required.
•
To stop a countdown operation completely, first pause it (by pressing
D
), and then
press
A
. This returns the countdown time to its starting value.
E-29
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
•
The display range of the stopwatch is 59 minutes, 59.99
seconds.
•
The stopwatch continues to run until you stop it. If it
reaches its limit, it restarts from zero.
•
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
C
(page E-9).
Minutes
Seconds