Operation Guide 5239
E-69
The period when summer time is applied in the location where you are using the
x
watch may be different from the period set for your currently selected Home City.
Use the procedure under “To switch between standard time and summer time
manually” (page E-39) to switch from
AUTO
to
STD
(for standard time) or
DST
(for
summer time).
■
The time and date settings are off.
This could indicate that the watch has been exposed to magnetism or strong impact,
which has caused problems with proper hand and day indicator alignment. Adjust the
watch’s hand and day indicator home position alignment (page E-63).
E-68
The time setting is being adjusted following a successful auto time calibration
x
signal receive operation (page E-19).
■
Hands suddenly stop moving. Button operation also is disabled.
The watch may be in the power recovery mode (page E-16). Do not perform any
operation until the hands return to their normal positions (in about 15 minutes). The
hands should return to their correct positions when normal operation returns. To help
power recover, leave the watch in a location where it is exposed to light.
■
The current time setting is off by hours.
Your Home City setting may be wrong. Check your Home City setting and correct it,
x
if necessary (page E-36).
■
The current time setting is off by one hour.
If you are using the watch in an area where time calibration signal reception is
x
possible, see “To confi gure Home City settings” (page E-36).
E-67
Troubleshooting
Hand Movement and Position
■
I lost track of what mode the watch is in.
Refer to “Mode Reference Guide” (page E-32). To return directly to the Timekeeping
Mode, hold down
C
at least two seconds.
■
The
x
Second Hand
is moving at two-second intervals.
■
All the watch’s hands are stopped at 12 o’clock and none of the buttons work
(
x
Second Hand
stopped at 57, 58, 59, or 00).
Power may be low. Expose the watch to light until the
x
Second Hand
starts moving
normally, at one-second intervals (page E-15).
■
The hands of the watch suddenly start moving at high speed, even when I do
not perform any operation.
This could be due to any one of the following causes. In all cases, the hand movement
does not indicate malfunction, and should stop shortly.
The watch is recovering from a sleep state (page E-18).
x
E-66
Press
3.
C
.
This enters the
x
n
Day Indicator
home position
adjustment mode.
Check the
4.
n
Day Indicator
to confi rm that it is
1
, which
is its home position.
If the
x
1
is not in the center of the
n
Day Indicator
,
rotate the crown to center it.
Rotating the crown three full consecutive turns
x
clockwise will cause the
n
Day Indicator
to start
changing in a forward direction (increment).
To stop
x
n
Day Indicator
movement, press any button.
Push the crown back in to return to the Timekeeping Mode.
5.
This will cause the hands to return to their normal positions and resume regular
x
timekeeping. Wait until everything stops moving before performing any other
operation.
6
E-65
To adjust home positions
Pull out the crown.
1.
Hold down
2.
B
for at least fi ve seconds until the watch
beeps and the
x
Second Hand
moves to 12 o’clock.
Automatic home position adjustment of all of the
x
hands (but not the
n
Day Indicator
) will start.
If all hands are at 12 o’clock (the proper home hand
x
home position), advance directly to step 3.
If the
x
v
Upper Dial Hand
is not pointing at
24
, which
is its home position, hold down
A
for about two
seconds to move it there.
6
@
>
E-64
Manual Home Position Adjustment
Perform the procedure in this section if auto home position adjustment is not possible
for some reason.
Hand home position adjustment is not required if the time and day settings are
x
correct.
Note
Any time after you enter the home position adjustment mode in step 2 of the
x
following procedure, you can return to the Timekeeping Mode by pushing the
crown back in. In this case, any adjustments you made before the watch returned
to the Timekeeping Mode will be applied.
If you do not perform any operation with the crown for about two minutes after
x
pulling it out, crown operations will become disabled and hands will not move if you
rotate the crown. If this happens, push the crown back in and then pull it out again.
E-63
Adjusting Home Positions
Strong magnetism or impact can cause the hands and/or day indicator setting to be
off, even if the watch is able to perform the time calibration signal receive operation.
Auto Home Position Adjustment
Auto correction of hand home positions corrects the hand position automatically.
Auto correction is performed in the Timekeeping Mode only.
x
Auto correction corrects the positions of all hands. For the day Indicator, you must
x
perform the manual adjustment procedure under “To adjust home positions” (page
E-65).
If the
x
v
Upper Dial Hand
is 12 hours off of the current correct time, correct the
setting using the procedure under “To adjust home positions” (page E-65).
Auto correction of the
x
b
Lower Dial Hand
is performed once a day in the middle of
the night, while the watch is in the sleep state (page E-18).
E-62
After the setting is the way you want, push the crown back in to exit the alarm
6.
setting mode.
The alarm always works based on the time kept in the Timekeeping Mode.
x
The watch will return to the Timekeeping Mode automatically if you do not
x
perform any operation in the Alarm Mode for about two or three minutes.
To turn the alarm on or off
In the Alarm Mode, press
A
to toggle the alarm between on and off. The
x
Second
Hand
will indicate the current ON/OFF setting.
Note
The alarm will not sound if battery power is low.
x
The alarm will not sound if the watch is in the Power Saving sleep state.
x
To stop the alarm
Press any button.
E-61
Rotate the crown to set the alarm time.
3.
The
x
z
Hour Hand
will also move.
See “Using the Crown” (page E-3) for information about high-speed hand
x
movement.
Press
4.
C
to switch to the hour setting mode.
The
x
z
Hour Hand
will move slightly left and right to indicate the
z
Hour Hand
setting mode.
Check the 24-hour time indicated by the
x
v
Upper Dial Hand
to see if the current
setting is a.m. or p.m.
Rotate the crown to adjust the hour setting only.
5.
See “Using the Crown” (page E-3) for information about high-speed hand
x
movement.
E-60
To change the alarm time setting
In the Timekeeping Mode, press
1.
C
three times to enter the Alarm Mode.
The
x
b
Lower Dial hand
will move to
AL
.
Pull out the crown to enter the alarm setting mode.
2.
If you do not perform any operation with the crown for about two minutes after
x
pulling it out, crown operations will become disabled and the watch hands will no
longer move when you rotate the crown. If this happens, push the crown back in
and then pull it out again.
You can toggle between the hour and minute setting mode, and the hour only
x
setting mode by pressing
C
.
Hour/Minute
Hour
C