manualshive.com logo in svg

Casio 3523, Operation Manual, Page: 10 / 11

Share
Download
Casio 3523 Operation Manual Download Page 10

Setting the Time

The countdown start time can be set in 1-
second units up to 24 hours.

●

If a timer countdown operation is in
progress, reset the timer to its current start
time before performing this operation.

l

Using the Timer

1.

Enter the Timer Mode.

l

Navigating Between Modes

2.

Press (A).

This causes the hours digits to flash.

Hours

3.

Use (B) to change the timer hour setting.

●

Holding down (B) scrolls through
settings at high speed.

4.

Press (C).

This causes the minutes digits to flash.

Minutes

5.

Use (B) to change the timer minute setting.

6.

Press (C).

This causes the seconds digits to flash.

Seconds

7.

Use (B) to change the timer seconds
setting.

8.

Press (D) to select Repeat Timer or Auto
Repeat Timer.

●

Each press of (D) toggles between
Repeat Timer and Auto Repeat Timer.

●

[AUTO] is displayed while Auto Repeat
is enabled.

9.

Press (A) to complete the setting
operation.

Note

●

While the setting is being configured,
the watch will exit the setting operation
automatically after about two or three
minutes of non-operation.

●

Setting a start time of [0:00 00] will
perform a countdown of 24 hours.

Using the Timer

1.

Enter the Timer Mode.

l

Navigating Between Modes

Hour, minute, second

2.

Use the operations below to perform a
timer operation.

B

B

B

(Time up)

Resume

Pause

(Countdown starts)

Start

●

A beeper will sound for 10 seconds to
let you know when the end of a
countdown is reached.

●

With Auto Repeat, the watch beeps
each second after the countdown
reaches 10 seconds.

●

To reset a paused countdown to the
start time, press (A).

3.

Press any button to stop the tone.

Note

●

If flash alert is enabled, display
illumination flashes along with the
beeper at the end of the countdown.
Pressing any button to stop the alarm
beeper also stops the flash alert
operation.

l

Configuring Flash Alert Settings

Watch Operation Guide 3523

10

Summary of Contents for 3523












Reviews:

No comments