Operation Guide 3419
E-39
Note
x
Once started, elapsed time measurement continues until you press
D
to stop
it, even if you change to a different mode and even if the stopwatch reaches
the elapsed time measurement limit.
x
If you change to another mode while a split time is frozen on the display, split
time display will be canceled.
E-38
To measure time with the stopwatch
●
The following shows button operations for stopwatch operations.
x
Elapsed time/cumulative time
D
D
D
D
A
Start
Stop
(Restart)
(Stop)
Reset
x
Split time (paused elapsed time reading)
D
A
A
D
A
Start
Split
Split time display
cancel
Stop
Reset
Pressing
A
while timing is being performed displays the split time (with [SPLIT]
fl ashing), but elapsed timing continues internally.
E-37
Stopwatch
The stopwatch measures elapsed time in units of 1/100 seconds up to 999 hours,
59 minutes, 59.99 seconds. Elapsed time returns to zero automatically and timing
continues from there when the maximum limit is reached.
To enter the Stopwatch Mode
●
In the Timekeeping Mode, press
C
four times to
enter the Stopwatch Mode.
See “Using Modes” (page E-14).
Seconds
Minutes
1/100 second
Hours
E-36
- Displaying the snooze setting screen
- Displaying the Timekeeping Mode setting screen
To test the alarm
●
In the Alarm Mode, hold down
D
to perform the tone/vibration alert
operations.
E-35
●
6
After all the settings are the way you want, press
A
to exit the setting
screen.
●
7
To return to the Timekeeping Mode, press
C
four times.
To stop a tone/vibration alert operation
●
Double-tapping the center of the watch display or pressing any one of the
buttons will stop an ongoing tone/vibration alert operation.
Note
x
In the case of snooze, the alarm will sound up to seven times at fi ve-minute
intervals.
x
The Snooze Indicator (SNZ) will fl ash on the display during the fi ve-minute intervals
between alarms.
x
Snooze will be canceled when any of the following occurs while the Snooze
Indicator (SNZ) is fl ashing on the display.
- Disabling snooze
E-34
●
3
To change an alarm time setting, hold down
A
for about two seconds until
the hour digits of the current alarm time start to fl ash.
[SET Hold] will appear on the display. After that, [SET
Hold] will disappear and the hour digits will fl ash.
●
4
Each press of
C
causes the fl ashing to move between the hour and the
minutes digits.
The fl ashing digits are the ones that are selected.
●
5
Use
B
and
D
to change the fl ashing setting, and set the hour and minutes
you want.
x
Holding down either button scrolls the setting at high speed.
x
If you are using 12-hour timekeeping, the PM indicator will appear for times
between noon and 11:59 p.m.
E-33
The alarm indicator is displayed while any alarm (Alarm 1 through Alarm 4) is
turned on, while the Hourly Time Signal indicator is displayed while the hourly
time signal is turned on.
While snooze is turned on, the Alarm Indicator and Snooze Indicator are both
displayed.
Hourly time signal on
Hourly time signal indicator
Alarm on
Alarm indicator
E-32
Snooze
: Alarm does not sound.
: Alarm sounds at the preset time, and up to seven times at fi ve-minute intervals
thereafter. This operation is performed only once.
: Alarm sounds at the preset time, and up to seven times at fi ve-minute intervals
thereafter. This operation is performed at the preset time each day.
E-31
●
2
Use
A
to toggle the displayed setting between on and off.
Alarm 1 through Alarm 4
: Alarm does not sound.
: Alarm sounds only once at the preset time and does not sound again after
that.
: Alarm sounds at the preset time each day.
Hourly time signal
: Hourly time signal does not sound.
: Hourly time signal sounds every hour on the hour.
E-30
To change an alarm setting
●
1
In the Alarm Mode, use
D
to select the alarm whose setting you want to
change.
Alarm 1
(
)
D
D
Alarm 2
(
)
Alarm 3
(
)
Alarm 4
(
)
Hourly Time
Signal (
)
Snooze Alarm
(
)
D
D
D
D