Operation Guide 3286
E-19
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
•
There are six screens in the Alarm Mode. Four are for
one-time alarms (indicated by numbers from
through
), one is for a snooze alarm (indicated by
), and one is for the Hourly Time Signal (indicated
by
).
•
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
C
(page
E-7).
Alarm time (Hour : Minutes)
On/Off status
Alarm number
E-18
•
Press
D
while a countdown operation is in progress to pause it. Press
D
again to
resume the countdown.
•
To completely stop a countdown operation, first pause it (by pressing
D
), and then
press
A
. This returns the countdown time to its starting value.
To set the countdown start time
1. In the Countdown Timer Mode, hold down
A
until the
hours of the countdown start time start to flash, which
indicates the setting screen.
2. Press
C
to move the flashing between the hours and
minutes.
3. While a setting is flashing, use
D
(+) or
B
(–) to
change it.
•
To set the starting value of the countdown time to
24 hours, set
.
4. Press
A
to exit the setting screen.
E-17
Countdown Timer
The countdown timer can be set within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
•
The countdown operation continues even if you exit the
Countdown Timer Mode.
•
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C
(page E-7).
To use the countdown timer
Press
D
while in the Countdown Timer Mode to start the
countdown timer.
•
When the end of the countdown is reached, the alarm
sounds for 1
0
seconds or until you stop it by pressing
any button. The countdown time is automatically reset to
its starting value after the alarm stops.
Hours Minutes
Seconds
E-16
To measure times with the stopwatch
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Start
Split
(
displayed)
Split release
Stop
Clear
Start
Split
Stop
Split release
Clear
Split Time
Two Finishes
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
E-15
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
•
The display range of the stopwatch is 59 minutes,
59.99 seconds.
•
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
C
(page E-7).
Minutes Seconds
1/100 second
E-14
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use
D
to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down
A
for about one second to toggle between
Daylight Saving Time (
DST
indicator displayed) and
Standard Time (
DST
indicator not displayed).
•
The
DST
indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
•
Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
•
In the World Time Mode, you can switch the city code
you currently have selected as your Timekeeping Mode
Home City between Standard Time and DST. The
setting you select in the World Time Mode will also be
applied in the Timekeeping Mode.
DST indicator
E-13
World Time
World Time shows the current time in 48 cities (29 time
zones) around the world.
•
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing
C
(page E-6).
To view the time for another city code
In the World Time Mode, press
D
to scroll eastwardly
through city codes.
•
For full information about city codes, see the “City Code
Table” at the back of this manual.
•
If the current time shown for a city is wrong, check your
Timekeeping Mode time and Home City code settings
and make the necessary changes.
Current time in the zone
of the selected city code
City code
E-12
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard
Time. Remember that not all countries or even local areas use Daylight Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
1. In the Timekeeping Mode, hold down
A
until the
seconds start to flash, which indicates the setting
screen.
2. Press
C
twice to display the DST setting screen.
3. Press
D
to toggle between Daylight Saving Time (
)
and Standard Time (
).
4. Press
A
to exit the setting screen.
•
The
DST
indicator is displayed on the Timekeeping
Mode and Alarm Mode screens while Daylight Saving
Time is turned on.
DST indicator
On/Off status
E-11
•
With the 12-hour format, the
P
(PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the
A
(AM) indicator appears for times in the range
of midnight to 11:59 a.m.
•
With the 24-hour format, times are displayed in the range of
0
:
00
to 23:59, without
any indicator.
•
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
•
The year can be set in the range of 2
000
to 2
0
99.
•
The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
•
The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
E-1
0
Screen
Do this:
Press
D
.
Use
D
(east) and
B
(west).
Press
D
.
Use
D
(+) and
B
(–).
Press
D
.
Use
D
(+) and
B
(–).
To do this:
Reset the seconds to
Change the city code
Toggle between Daylight Saving Time (
)
and Standard Time (
)
Change the hour or minutes
Toggle between 12-hour (
) and 24-hour
(
) timekeeping
Change the year, month, or day
•
See “Daylight Saving Time (DST)” (page E-12) for details about the DST setting.
4. Press
A
to exit the setting screen.
•
Resetting the seconds to
while the current count is in the range of 3
0
to 59
causes the minutes to be increased by 1. In the range of
00
to 29, the seconds are
reset to
without changing the minutes.
