Operation Guide 3227
E-20
To set an alarm time
1. In the Alarm Mode, use
E
and
D
to scroll through the
alarm screens until the one whose time you want to set
is displayed.
•
You can configure Alarm
1
as a snooze alarm or a
one-time-alarm. Alarms
2
through
5
can be used as
one-time alarms only.
•
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down
A
until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
•
This operation automatically turns on the alarm.
Alarm
1
Alarm
2
Alarm
3
Hourly Time
Signal
Alarm
5
Alarm
4
Press
E
.
Press
D
.
Alarm 2 on indicator
Hour : Minutes
Alarm number
AM Indicator
Month–Day
E-21
3. Use
C
and
B
to move the flashing in the sequence shown below to select other
settings.
4. While a setting is flashing, use
E
(+) and
D
(–) to change it.
•
To set an alarm that does not include a month (Daily alarm, Monthly alarm), set
x
for the month. Use
E
and
D
until the
x
mark appears (between
and ) while
month setting is flashing.
•
To set an alarm that does not include a day (Daily alarm, 1-Month alarm), set
xx
for the day. Use
E
and
D
until the
xx
mark appears (between the end of the
month and ) while the day setting is flashing.
•
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (
A
indicator) or p.m. (
P
indicator).
5. Press
A
to exit the setting screen.
Minutes
Hour
Month
Day
Press
C
.
Press
B
.
E-22
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm tone operation is performed a
total of seven times, every five minutes, until you turn the alarm off or change it to a
one-time alarm (page E-24).
•
Pressing any button stops the alarm tone operation.
•
Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-6)
Displaying the alarm
1
setting screen (page E-20)
To test the alarm
In the Alarm Mode, hold down
C
to sound the alarm.
•
Pressing
C
also toggles the currently display alarm or the Hourly Time Signal on
and off.
E-23
To turn Alarms
2
through
5
and the Hourly Time Signal on and off
1. In the Alarm Mode, use
E
and
D
to select a one-time
alarm (alarm
2
through
5
) or the Hourly Time Signal.
2. Press
C
to toggle it on and off.
•
The current on/off status of Alarms
2
through
5
is
shown by indicators (
AL-2
through
AL-5
). The
SIG
indicator shows the on (
SIG
displayed)/off (
SIG
not
displayed) status of the Hourly Time Signal.
•
The alarm on indicators and Hourly Time Signal on
indicator are displayed in all modes.
•
While an alarm is sounding, the applicable alarm on
indicator flashes on the display.
Alarm on indicators
Hourly Time Signal
on indicator
E-24
To select the operation of Alarm
1
1. In the Alarm Mode, use
E
and
D
to select Alarm
1
.
2. Press
C
to cycle through the available settings in the sequence shown below.
•
The
SNZ
indicator and Alarm
1
on indicator (
AL-1
) are displayed in all modes.
•
The
SNZ
indicator flashes during the 5-minute intervals between alarms.
•
The alarm indicator (
AL-1
and/or
SNZ
) flashes while the alarm is sounding.
SNZ indicator and Alarm
1
on indicator
Snooze alarm on
One-time alarm on
Alarm off
C
C
C
E-25
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
•
The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
•
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•
The elapsed time measurement operation continues
even if you exit the Stopwatch Mode.
•
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
B
(page
E-5).
1/100 second
Hours
Minutes
Seconds
Timekeeping
Mode time
E-26
To measure times with the stopwatch
C
Start
Stop
Elapsed Time
➤
Re-start
Clear
C
➤
Stop
C
➤
C
➤
A
Split Time
C
Start
Split
➤
Split release
Clear
A
➤
Stop
A
➤
C
➤
A
Two Finishes
C
Start
Split
➤
Stop
Clear
A
➤
Split release
C
➤
A
➤
A
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
(
SPL
displayed)
E-27
Countdown Timer
The countdown timer can be set within a range of 1
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
•
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
B
(page E-5).
To set the countdown start time
1. In the Countdown Timer Mode, hold down
A
until the
hour setting of the countdown start time starts to flash,
which indicates the setting screen.
2. Press
B
or
C
to move the flashing between the hour
and minute settings.
3. While a setting is flashing, use
E
(+) and
D
(–) to change it.
•
To set the starting value of the countdown time to 24 hours, set
0:00
.
4. Press
A
to exit the setting screen.
Hours
Minutes
Seconds
Timekeeping Mode time
E-28
To use the countdown timer
Press
C
while in the Countdown Timer Mode to start the countdown timer.
•
When the end of the countdown is reached, the alarm sounds for 10 seconds or until
you press any button to stop it. The countdown time is automatically reset to its
starting value after the alarm stops.
•
The countdown timer operation continues even if you exit the Countdown Timer
Mode.
•
Press
C
while a countdown operation is in progress to pause it. Press
C
again to
resume the countdown.
•
To stop a countdown operation completely, first pause it (by pressing
C
), and then
press
A
. This returns the countdown time to its starting value.
E-29
Dual Time
The Dual Time Mode lets you keep track of time in a
different time zone. You can select Standard Time or
Daylight Saving Time for the Dual Time Mode time, and a
simple operation lets you view the Timekeeping Mode
screen or Data Bank Mode screen.
•
The seconds count of the Dual Time is synchronized
with the seconds count of the Timekeeping Mode.
•
All of the operations in this section are performed in the
Dual Time Mode, which you enter by pressing
B
(page
E-5).
To set the Dual Time
1. In the Dual Time Mode, hold down
A
until the hour setting start to flash, which
indicates the setting screen.
2. Press
B
or
C
to move the flashing between the hour and minute settings.
3. While a setting is flashing, use
E
(+) and
D
(–) to change it.
4. Press
A
to exit the setting screen.
Dual time
(Hour : Minutes Seconds)
Timekeeping Mode time