Operation Guide 3214
1
MO1005-EA
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
Warning!
•
The measurement functions built into this watch are not intended for taking
measurements that require professional or industrial precision. Values produced
by this watch should be considered as reasonable representations only.
•
The Moon phase indicator and tide graph data that appear on the display of this
watch are not intended for navigation purposes. Always use proper instruments
and resources to obtain data for navigation purposes.
•
This watch is not an instrument for calculating low tide and high tide times. The
tide graph of this watch is intended to provide a reasonable approximation of
tidal movements only.
•
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of this
product or its malfunction.
Keep the watch exposed to bright light
The electricity generated by the solar cell of the watch is
stored by a rechargeable battery. Leaving or using the
watch where it is not exposed to light causes the battery
to run down. Make sure the watch is exposed to light as
much as possible.
•
When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright
light.
•
You should try to keep the watch outside of your sleeve
as much as possible. Charging is reduced significantly if
the face is covered only partially.
ll
l
l
l
l
l
l
l
l
l
Bright Light
Solar cell
All
functions
enabled
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Charge
Rechargeable battery
Bright Light
Electrical
energy
Solar cell
(Converts light to
electrical power.)
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Some or all
functions
disabled
Dis-
charge
Battery charges in the light.
Battery discharges in the dark.
•
The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will result in some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
•
The actual level at which some functions are disabled depends on the watch model.
•
Frequent display illumination can run down the battery quickly and require charging.
The following guidelines give an idea of the charging time required to recover from a
single illumination operation.
Approximately 5 minutes exposure to bright sunlight coming in through a window
Approximately about 8 hours exposure to indoor fluorescent lighting
•
Be sure to read “Power Supply” for important information you need to know
when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving function
has turned off the display to conserve power.
•
See “Power Saving Function” for more information.
About This Manual
•
Button operations are indicated using the letters shown in the illustration.
•
Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the “Reference” section.
Countdown Timer Mode
Stopwatch Mode
Alarm Mode
▲
World Time Mode
▲
ll
llll
ll
l lll
▲
▲
General Guide
•
Press
C
to change from mode to mode.
•
In any mode (except when a setting screen is on the display), press
B
to illuminate
the display.
Timekeeping Mode
Press
C
.
▲
llll
ll
lllll
llll
ll
lllll
▲
Tide/Moon Data Mode
Timekeeping
Press the
A
button to toggle the upper display between the day of the week and
date, and the currently selected World Time city and time (Dual Time).
Use the Timekeeping Mode to set and view the current time and date.
A
A
Current Time
llll
ll
lllll
PM indicator
Hour : Minutes
Seconds
Day of week
Month – Day
Dual Time
llll
ll
lllll
Dual time
City code
▲
▲
Read This Before You Set the Time and Date!
This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the time, it is important that you first
select the correct city code for your Home City (the city where you normally use the
watch). If your location is not included in the preset city codes, select the preset city
code that is in the same time zone as your location.
•
Note that all of the times for the World Time Mode city codes are displayed in
accordance with the time and date settings you configure in the Timekeeping Mode.
To set the time and date manually
1. In the Timekeeping Mode hold down
A
until the city
code starts to flash, which indicates the setting screen.
2. Use
D
and
B
to select the city code you want.
•
Make sure you select your Home City code before
changing any other setting.
•
For full information on city codes, see the “City Code
Table”.
l l l
ll
ll
ll
ll
ll
l l l
3. Press
C
to move the flashing in the sequence shown below to select the other
settings.
Seconds
12/24-Hour
Format
Hour
Minutes
DST
Month
Year
City Code
Day
Power Saving
Illumination
Duration
Button
Operation Tone
•
The following steps explain how to configure timekeeping settings only.
4. When the timekeeping setting you want to change is flashing, use
D
or
B
to
change it as described below.
Change the city code
Toggle between Daylight Saving Time (
ON
)
and Standard Time (
OFF
).
Toggle between 12-hour (
) and 24-
hour (
) timekeeping
Reset the seconds to
Change the hour and minutes
Use
D
(east) and
B
(west).
Press
D
.
Press
D
.
Press
D
.
Use
D
(+) and
B
(–).
Screen:
To do this:
Do this:
5. Press
A
to exit the setting screen.
•
The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Change the year, month, or day
Toggle the button operation tone between
(on) and
(off)
Toggle the illumination duration between
(approximately 1.5 seconds) and
(approximately 3 seconds).
Toggle between Power Saving on (
) and
off (
)
Use
D
(+) and
B
(–).
Press
D
.
Press
D
.
Press
D
.
/
