Operation Guide 3155
3
To turn auto receive on and off
1. In the Timekeeping Mode, press
D
to display the last
successful receive time and date screen.
2. Hold down
A
until the current auto receive setting (
ON
or
OFF
) starts to flash. This is the setting screen.
•
Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press
D
to toggle auto receive on (
ON
) and off (
OFF
).
4. Press
A
to exit the setting screen.
•
For information about city codes that support signal
receive, see “To specify your Home City”.
To check the latest signal reception results
Press
D
to view the last successful receive time and
date. Press
D
again to return to the previous screen.
lll
lll
ll
ll
l l l
l
ll
ll
ll
ll
l
l l
l l l
On/Off status
•
Enter the Timekeeping Mode
and try again.
•
Select
LIS
,
LON
,
MAD
,
PAR
,
ROM
,
BER
,
STO
,
ATH
,
MOW
,
HKG
,
BJS
,
TPE
,
SEL
,
TYO
,
HNL
,
ANC
,
YVR
,
LAX
,
YEA
,
DEN
,
MEX
,
CHI
,
MIA
,
YTO
,
NYC
,
YHZ
, or
YYT
as your
Home City.
•
Perform manual signal receive
or wait until the next auto
signal receive operation is
performed.
•
Check to make sure the watch
is in a location where it can
receive the signal.
Cannot perform
manual receive.
Auto receive is
turned on, but the
settings updated
indicator does not
appear on the
display.
•
The watch is not in the Timekeeping
Mode.
•
Your current Home City is not one of
the following:
LIS
,
LON
,
MAD
,
PAR
,
ROM
,
BER
,
STO
,
ATH
,
MOW
,
HKG
,
BJS
,
TPE
,
SEL
,
TYO
,
HNL
,
ANC
,
YVR
,
LAX
,
YEA
,
DEN
,
MEX
,
CHI
,
MIA
,
YTO
,
NYC
,
YHZ
, or
YYT
•
You changed the time setting
manually.
•
The DST setting was changed
manually in the World Time Mode.
•
You pressed a button while signal
receive was in progress.
•
Even if receive is successful, the
settings updated indicator
disappears from the display each
day when the first auto receive
operation of the day is performed.
•
Time data (hour, minutes, seconds)
only was received during the last
receive operation. The settings
updated indicator appears only
when time data and date data (year,
month, day) are both received.
What you should do
Problem
Probable Cause
Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal reception.
•
If the time is one hour off, the DST
setting may be incorrect.
•
The Home City code setting is not
correct for the area where you are
using the watch.
Time setting is
incorrect following
signal reception.
•
Change the DST setting to
Auto DST.
•
Select the correct Home City
code.
•
For further information, see “Important!” under “Time Calibration Signal Reception”
and “Radio-controlled Atomic Timekeeping Precautions”.
Rally Mode
The Rally Mode of your watch can be used to measure special stage elapsed time,
and to keep track of the goal target time (countdown). The Rally Mode timing
operation is shown in the illustration below.
lll
llll
ll
lll
llll
ll
lll
llll
ll
l
ll
ll
llll
ll
ll
lll
llll
ll
l
l l
ll
ll
ll
ll
ll
ll
ll
l l
l l l
ll
lllll
ll
l
l ll
ll
ll
ll
ll
l l l
Start point
D
Start
D
Stop
B
Record elapsed time
The watch returns to the reset
screen automatically when the
target time becomes zero.
Special stage (competitive section 42' 30" 0)
Target time (0:50)
Special stage time
measurement end
Goal
Road section (non-competitive 07' 30" 0)
Remaining
target time
(hours:minutes)
Elapsed time
1/10-second indicator
Special stage elapsed
time (hours, minutes,
seconds, 1/10-second)
Remaining target time
(minutes, seconds)
Special Stage Elapsed Time Measurement
The special stage elapsed time is measured up to 99 hours, 59 minutes, 59.9
seconds. If the time exceeds this, timing reverts to zero and continues from there.
Before Starting Measurement
The watch comes with 10 preset target times (link times),
which you can use as-is or change to the value you want.
You can use the
B
button to select the target time you
want while the current target time is reset to its initial
value.
LT-01
0:10
LT-07
1:30
LT-02
0:20
LT-08
2:00
LT-03
0:30
LT-09
3:00
LT-04
0:40
LT-10
5:00
LT-05
0:50
OFF
LT-06
1:00
LT-05
LT-05 target time (0:50)
To change a target time
1. While the current target time is reset to its initial value in
the Rally Mode, hold down
A
until the display contents
start to flash. This is the setting screen.
2. Use the
D
(+) and
B
(–) buttons to select the target
(link) time you want to change.
3. Press the
C
button so the current target time’s hour
digit starts to flash.
4. Use the
D
(+) and
B
(–) buttons to change the hour digit value.
5. Press the
C
button to move the flashing to the minute digits.
6. Use the
D
(+) and
B
(–) buttons to change the minute digit value.
ll
ll
ll
lll
llll
ll
lll
ll
l ll
7. After the time is setting you want, press the
A
button to exit the setting screen.
You can set a target time up to 24 hours, in units of one minute.
Target (link) time
number
Target time hours
Target time
minutes
C
C
C
To start a Rally Mode time measurement
Press the
D
button to start the auto start countdown.
Time measurement (special stage) will start when the
auto start countdown reaches 00 seconds.
•
The watch will beep and display illumination will flash
whenever the remaining auto countdown time reaches
50, 40, 30, 20, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1 and 0 seconds.
•
You can cancel the auto start countdown at any point
and start time measurement (special stage) manually by
pressing the
D
button.
•
You can cancel the countdown and return to the
countdown start screen by pressing the
B
button while
a countdown is in progress.
Auto start countdown
seconds indicator
Remaining auto start
countdown time
(36 seconds indicated here)
Special Stage Timing
This section describes operations you can perform while
special stage timing is in progress.
To pause the current time on the display
While a special stage timing operation is in progress press
the
D
button.
•
This will pause the current elapsed time (flashing) on the
display for about one or two minutes. Though the time is
frozen on the display, the watch continues the special
stage timing operation (and count down of the remaining
target time) internally.
•
While a time is paused on the display, you can record it
in memory or reset the timing operation to zero. If you
don’t do anything, the display will return to the normal
elapsed time measurement screen after a few minutes.
l l
ll
ll
ll
ll
ll
ll
ll
l l
l l l
ll
lllll
ll
l
l ll
ll
ll
ll
ll
l l l
Measured elapsed time
Target time
To record the time paused on the display
While a time is paused on the display (see above), press the
B
button.
•
This will save the paused time in memory and display the ongoing special stage
timing operation.
•
The watch has enough memory to store up to 30 measurement time records. If there
are already 30 records in memory, storing a new measurement time causes the
oldest record to be deleted automatically to make room for the new one.
To reset the timing operation to zero
While a time is paused on the display (see above), hold down the
B
button.
•
This will reset the elapsed time operation to zero.
To cancel an ongoing elapsed time measurement operation
Hold down the
B
button to reset the elapsed time operation to zero.
To change screen contents during elapsed time measurement
Press the
B
button to display the remaining target time. Note that this operation is not
available if “OFF” is selected for the target time.
ll
lllll
ll
l
When the remaining target
time is 5 minutes or more
lll
llll
ll
lll
llll
ll
When the remaining target time is
less than 5 minutes
Target
time
Target
time
Remaining Target Time Alert
The watch will beep and display illumination will flash when the remaining target time
reaches the following points, 5, 3 and 1 minute, and 30, 10, 5, 4, 3, 2, and 1 second
before time up, and at time up.
