Operation Guide 3148
1
MO1203-ED
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out
of your purchase, be sure to read this manual carefully.
Applications
The built-in sensors of this watch measure barometric pressure, temperature
and altitude. Measured values are then shown on the display. Such features
make this watch useful when hiking, mountain climbing, or when engaging in
other such outdoor activities.
Keep the watch exposed to bright light
The electricity generated by the solar cell of the
watch is stored by a built-in battery. Leaving or
using the watch where it is not exposed to light
causes the battery to run down. Make sure the
watch is exposed to light as much as possible.
•
When you are not wearing the watch on your
wrist, position the face so it is pointed at a
source of bright light.
•
You should try to keep the watch outside of
your sleeve as much as possible. Charging is
reduced significantly if the face is covered only
partially.
ll
l
l
l
l
l
l
l
l
l
Bright light
Solar cell
•
The watch continues to operate, even when it is not exposed to light.
Leaving the watch in the dark can cause the battery to run down, which will
cause some watch functions to be disabled. If the battery goes dead, you
will have to re-configure watch settings after recharging. To ensure normal
watch operation, be sure to keep it exposed to light as much as possible.
Bright light
Electrical
energy
All
functions
enabled
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Charge
Solar cell
(Converts light to
electrical power.)
Rechargeable battery
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Some
functions
disabled
Dis-
charge
Battery charges in the light.
Battery discharges in the dark.
•
The actual level at which some functions are disabled depends on the
watch model.
•
Frequent display illumination can run down the battery quickly and require
charging. The following guidelines give an idea of the charging time
required to recover from a single illumination operation.
Approximately five minutes exposure to bright sunlight coming in through
a window
Approximately 50 minutes exposure to indoor fluorescent lighting
•
Be sure to read “Power Supply” for important information you need to
know when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving
function has turned off the display to conserve power.
•
See “Power Saving” for more information.
Warning!
•
The measurement functions built into this watch are not intended for
taking measurements that require professional or industrial precision.
Values produced by this watch should be considered as reasonable
representations only.
•
CASIO COMPUTER CO., LTD. assumes no responsibility for any loss,
or any claims by third parties that may arise through the use of this
watch.
About This Manual
(Light)
(Light)
•
Button operations are indicated using the letters shown in the illustration.
•
Each section of this manual provides you with the information you need to
perform operations in each mode. Further details and technical information
can be found in the “Reference” section.
General Guide
•
The illustration below shows which buttons you need to press to navigate
between modes.
•
In any mode, press
L
to illuminate the display.
•
You can press the
C
button to go directly from the Timekeeping Mode to the
Altimeter Mode. To go to the Altimeter Mode from the Barometer/
Thermometer, World Time, Stopwatch, Countdown Timer, Alarm, or Data
Recall Mode, first enter the Timekeeping Mode and then press the
C
button.
Timekeeping Mode
Altimeter Mode
World Time Mode
Data Recall Mode
Countdown
Timer Mode
Press
D
.
Stopwatch Mode
Barometer/
Thermometer Mode
Alarm Mode
▲
▲
▲
▲
Press
D
.
▲
Press
C
.
▲
▲
▲
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
•
In the Timekeeping Mode, you can use the buttons shown in the illustration
to display the timekeeping display you want.
•
Pressing the
B
button once will display the current time in the city you last
viewed in the World Time Mode.
•
Holding down the
B
button for about five seconds will swap the World
Time City and your current Home Time City.
•
To swap the cities back again, hold down the
B
button for about five
seconds again.
TYO Time
City you last viewed in the
World Time Mode
▲
▲
▲
▲
▲
▲
Day of week
Seconds
Hour :
Minutes
Hold down
B
for
five seconds.
Hold down
B
for
five seconds.
Release
B
.
B
Release
B
.
B
Time in city
you last
viewed in the
World Time
Mode
Time in city
you last viewed
in the World
Time Mode
TYO Time
TYO Time
Time in city you last viewed
in the World Time Mode
UTC Time
