Operation Guide 2931
10
❚
Daily Alarm (AL1, AL2, AL3)
The watch performs an alert operation (beep or vibration) for
about 10 seconds when an alarm time is reached.
❚
Snooze Alarm (SNZ)
With the snooze alarm, the watch performs an alert operation
(beep or vibration) for 10 seconds when the alarm time is reached,
and up to seven times at five-minute intervals thereafter. Pressing
any button stops the alert operation, but the alert operation will be
performed again after five minutes.
❚
Hourly Time Signal
The hourly time signal causes the watch to beep or vibrate every
hour on the hour.
Whether the watch beeps or vibrates depends on the current
alert setting. See “Selecting Beeper or Vibration Alert” for
more information.
❚
To set an alarm time
1.
In the Alarm Mode, use the
D
D
D
D
D
button to scroll
through the alarm screens
in the sequence shown
below until the one you
want is displayed.
•
Each press of the
D
button
cycles through alarm screens
in the sequence shown below.
Alarm 3
(AL3)
Alarm 1
(AL1)
Alarm 2
(AL2)
Hourly Time
Signal (SIG)
Snooze Alarm
(SNZ)
2.
When the alarm you want
to set is displayed, hold
down the
A
A
A
A
A
button for
about two seconds until
the hour digits start to
flash on the display.
•
This also causes the alarm
indicator to appear, and turns
on the alarm automatically.
The snooze alarm screen also
has a snooze indicator (SNZ).
(Forward)
Alarm Number
Hour
Alarm Indicator
Using the Alarms and Hourly Time Signal
Use the
C
C
C
C
C
button to enter the Alarm Mode as
shown under “Modes and Display Screens”.
3.
Press the
C
C
C
C
C
button to
select the setting you
want to change.
•
Each press of
C
moves the
flashing between the hour and
minute as shown below.
4.
Use the
D
D
D
D
D
(+) and
B
B
B
B
B
(–)
buttons to change each
setting.
•
Holding down either button
changes the setting at high
speed.
Repeat steps 3 and 4 to set the time you want.
•
When setting the hour, make sure you specify AM (no indicator) or
PM (P) correctly when using 12-hour timekeeping, or that you
specify the correct 24-hour time.
•
The same 12-hour/24-hour format you select for the Timekeeping
Mode time is also applied in the Alarm Mode.
5.
When the alarm time is the way you want, press the
A
A
A
A
A
button to exit the setting screen.
•
The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
❚
To turn an alarm on or off
1.
In the Alarm Mode, use the
D
D
D
D
D
button to display the
screen for the alarm you want to turn on or off.
2.
Press the
A
A
A
A
A
button to toggle the displayed alarm on or
off.
•
Turning on an alarm or the Hourly Time Signal causes its
indicator to appear on the display. The snooze alarm screen
also has a snooze indicator (SNZ).
Alarm 1 Screen
Alarm Indicator
Snooze Alarm Screen
Alarm Indicator
Snooze Indicator
(Decrease)
(Increase)
Hour Minutes
❚
To stop an alert operation
Press any button.
•
In the case of the snooze alarm the alert operation will be
performed again in about five minutes. The snooze indicator
flashes while the snooze alarm is active (indicating that the alert
operation will be performed again).
•
The snooze alarm will be canceled automatically when any one of
the following occurs while the SNZ indicator is flashing on the
display.
•
Turning off the snooze alarm
•
Displaying the snooze alarm setting screen
•
Displaying the Timekeeping Mode setting screen
❚
To test the alert operation
In the Alarm Mode, hold down the
D
button to perform the alert
operation.
❚
To turning the hourly time signal on and off
1.
In the Alarm Mode, use the
D
D
D
D
D
button to display the screen
for the hourly time signal (SIG).
2.
Press the
A
A
A
A
A
button.
•
Press the
A
button to toggle the hourly time signal on or off.
•
Turning on an alarm or the Hourly Time Signal causes its
indicator to appear on the display.
Hourly Time Signal Screen
Hourly Time Signal Indicator
