4
Operation Guide 2877
More than 15 degrees
too high
Auto light switch precautions
•
Wearing the watch on the inside of your wrist and movement or vibration of your arm
can cause the auto light switch to activate and illuminate the display. To avoid
running down the battery, turn off the auto light switch whenever engaging in
activities that might cause frequent illumination of the display.
•
Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
•
Illumination turns off after the preset illumination
duration (see “To specify the illumination duration”),
even if you keep the watch pointed towards your face.
•
Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back towards your face again. If this
does not work, drop your arm all the way down so it hangs at your side, and then
bring it back up again.
•
Under certain conditions, illumination does not turn on until about one second after
you turn the face of the watch towards you. This does not indicate malfunction.
•
You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
,
, and
Messages
•
Performing any button operation that stores or recalls run data will cause
to
appear if battery power is low. Buttons will also become disabled for a few seconds.
Normal operation will return when battery power recovers.
•
When the AC (all clear) operation is performed after the watch’s battery is replaced,
the message
will remain on the display for a few minutes as the watch
performs a memory check. Do not perform any button operation while
is on
the display.
•
If
appears on the display, it means that the back of the watch is open or loose,
which is causing improper contact inside the watch. Whenever the message
appears on the display of the watch and stays there, take the watch to the store
where you purchased it or to your local CASIO distributor.
•
Performing the AC (all clear) operation will cause all data currently stored in watch
memory to be deleted. Be sure to always keep separate written copies of all
important data.
*Based on data as of June 2004.
–11
–11.0
Pago Pago
HNL
Honolulu
–10.0
Papeete
ANC
Anchorage
–09.0
Nome
LAX
Los Angeles
–08.0
San Francisco, Las Vegas, Vancouver, Seattle/Tacoma,
Dawson City
DEN
Denver
–07.0
El Paso, Edmonton
CHI
Chicago
–06.0
Houston, Dallas/Fort Worth, New Orleans,
Mexico City, Winnipeg
NYC
New York
–05.0
Montreal, Detroit, Miami, Boston, Panama City,
Havana, Lima, Bogota
CCS
Caracas
–04.0
La Paz, Santiago, Port Of Spain
RIO
Rio De Janeiro
–03.0
Sao Paulo, Buenos Aires, Brasilia, Montevideo
–2
–02.0
–1
–01.0
Praia
GMT
+00.0
Dublin, Lisbon, Casablanca, Dakar, Abidjan
LON
London
PAR
Paris
+01.0
Milan, Rome, Madrid, Amsterdam, Algiers, Berlin,
Hamburg, Frankfurt, Vienna, Stockholm
CAI
Cairo
+02.0
Athens, Helsinki, Istanbul, Beirut, Damascus,
JRS
Jerusalem
Cape Town
JED
Jeddah
+03.0
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi, Moscow
THR
Tehran
+03.5
Shiraz
DXB
Dubai
+04.0
Abu Dhabi, Muscat
KBL
Kabul
+04.5
KHI
Karachi
+05.0
Male
DEL
Delhi
+05.5
Mumbai, Kolkata
DAC
Dhaka
+06.0
Colombo
RGN
Yangon
+06.5
BKK
Bangkok
+07.0
Jakarta, Phnom Penh, Hanoi, Vientiane
HKG
Hong Kong
+08.0
Singapore, Kuala Lumpur, Beijing, Taipei, Manila,
Perth, Ulaanbaatar
TYO
Tokyo
+09.0
Seoul, Pyongyang
ADL
Adelaide
+09.5
Darwin
SYD
Sydney
+10.0
Melbourne, Guam, Rabaul
NOU
Noumea
+11.0
Port Vila
WLG
Wellington
+12.0
Christchurch, Nadi, Nauru Island
City
City
GMT
Other major cities in same time zone
Code
Differential
City Code Table
