USER’S GUIDE 2709
1
About This Manual
•
Button operations are indicated using the letters shown
in the illustration.
•
Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
General Guide
•
Press
C
to change from mode to mode.
•
In any mode, press
L
to illuminate the display.
Data Memory Mode
Stopwatch Mode
Timekeeping Mode
Alarm Mode
▲
▲
▲
Hand Setting Mode
▲
▲
Press
C
.
▲
World Time Mode
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
•
In the Timekeeping Mode, press
D
to change the screen format as shown below.
Press
D
.
▲
▲
Date and Time
Analog
Seconds
Date
Seconds and Date
▲
Seconds
Hour : Minutes
Month – Day
Day of week
PM
indicator
▲
▲
•
Pressing
A
displays the Last Signal screen (date and time the time calibration
signal was last received) in the Timekeeping Mode.
Current Time Setting
This watch automatically adjusts its time setting in accordance with a time calibration
signal. You can also perform a manual procedure to set the time and date, when
necessary.
•
Before using the watch in the Continental United States, first use the procedure
under “Setting Up the Watch for Use in the Continental United States” to set the time
in accordance with a time calibration signal.
•
Note that after you set your Home City (the city where you normally use the watch)
code, you must also turn on the watch’s time calibration signal receiver if you want to
enable auto time calibration. See “About Auto Receive” for more information.
•
See “Setting the Digital Time and Date Manually” for information about manual
settings.
•
The analog time of this watch is synchronized with the digital time. Because of this,
the analog time setting is automatically adjusted whenever you change the digital
setting. See “Analog Timekeeping” for more information.
•
Before using the watch in Japan, first specify your Home City, select the DST setting
you want to use, and then perform the procedure under “To perform manual time
calibration signal reception”.
Last Signal Screen
▲
Press
A
.
Receive date
Receive time
▲
Setting Up the Watch for Use in the Continental United States
You need to make the following three settings before using this watch in the
Continental United States. The following provides a general overview of the setting
procedure. For full details, see “Setting the Time and Date Manually” and “Time
Calibration Signal Reception”.
•
Specify the city code for your Home City (the city where you will normally use the
watch).
•
Select the auto summer time (DST) setting.
•
Perform the manual time calibration signal receive operation to set the current time.
To set up the watch for use in the Continental United States
1. In the Timekeeping Mode, press
B
. This causes the
current auto receive on/off setting (the receive indicator)
to flash, which indicates the setting screen.
2. Press
C
twice to move the flashing to the city code
setting.
3. Use
D
(+) and
A
(–) to select the city code you want to
use as your Home City.
l l l l
ll
ll
ll
ll
ll
l l
City code
Receive indicator
GMT differential
•
The following are the city codes for major cities in the
Continental United States time zones.
LAX
: Los Angeles, San Francisco, Las Vegas, Seattle
DEN
: Denver, El Paso
CHI
: Chicago, Houston, Dallas/Fort Worth, New Orleans
NYC
: New York, Detroit, Miami, Boston
4. Press
C
to display the summer time (DST) setting
screen.
5. Use
D
to select
AUTO DST
.
•
AUTO DST
specifies auto switching between Daylight
Saving Time and Standard Time.
6. Press
B
to exit the setting screen.
•
If you changed the digital time setting with the above
steps, the analog hands move at this time to match it.
Wait until the analog hands stop moving before you
advance to the next step.
7. Hold down
A
for about two seconds until the watch
beeps.
•
Release
A
and the message
receiving
appears to
indicate that signal reception has started.
•
Time calibration signal reception takes from two to six
minutes. Take care that you do not move the watch
during this time.
•
If the watch is indoors, we recommend that you place
the watch near a window to allow better signal
reception.
•
After signal reception is complete, the display of the
watch changes to the Last Signal screen, and the
analog time of the watch is adjusted automatically.
l l l ll
lll
ll
ll
Receive indicator
Time Calibration Signal Reception
This watch is designed to pick up a time calibration signal and update its time setting
in accordance with the signal. There are two different methods you can use to receive
the signal:
Auto Receive
and
Manual Receive
. With
Auto Receive
, the watch
automatically receives the calibration signal three times each day and makes
appropriate adjustments. With
Manual Receive
, you perform a specific button
operation to receive the calibration signal.
Before performing a signal receive operation, remove the watch from you wrist and
position it as shown in the illustrations below.
•
If your watch has a resin band, pass the end of the band through the band loop and
place the watch on a stable surface.
Resin band
Metal band
Pass through band loop.