background image

INTRODUCTION

WARNING

Flying objects!
Do not use the implement at a higher Power Take-Off (PTO) RPM than recommended. Machine damage
due to vibration may occur, resulting in loose parts and flying debris.
Failure to comply could result in death or serious injury.

W0192A

Battery and electrical system

WARNING

Explosive gas!
Batteries emit explosive hydrogen gas and other fumes while charging. Ventilate the charging area.
Keep the battery away from sparks, open flames, and other ignition sources. Never charge a frozen
battery.
Failure to comply could result in death or serious injury.

W0005A

WARNING

Battery acid causes burns. Batteries contain sulfuric acid.
Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush
with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large
quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.
Failure to comply could result in death or serious injury.

W0111A

WARNING

Battery gas can explode!
To prevent an explosion: 1. Always disconnect the negative (-) battery cable first. 2. Always connect
the negative (-) battery cable last. 3. Do not short circuit the battery posts with metal objects. 4. Do
not weld, grind, or smoke near a battery.
Failure to comply could result in death or serious injury.

W0011A

NOTICE:

never check the remaining battery charge by shorting out the terminals. This will result in a spark and may

cause an explosion or fire. Use a hydrometer to check the remaining battery charge.

NOTICE:

check the electrical harnesses for cracks, abrasions, and damaged or corroded connectors. Always keep

the connectors and terminals clean.

Hydraulic system

WARNING

Burn hazard!
Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid
temperature should not exceed 40 °C (104 °F).
Failure to comply could result in death or serious injury.

W0241A

WARNING

Pressurized fluid can penetrate the skin and cause severe injuries.
The grease in the cylinder is under high pressure. Never loosen the grease fitting adaptor completely
in order to speed up the flow of grease.
Failure to comply could result in death or serious injury.

W0261A

48098410 16/05/2017

8

Summary of Contents for CX80C























Reviews: