background image

INTRODUCTION

Safety rules - Personal safety

Preliminary warnings to maintenance operation

WARNING

Avoid injury!
Shut off the engine, remove the key, and make sure all machine motion stops before you service the
machine.
Failure to comply could result in death or serious injury.

W1128B

WARNING

Improper operation or service of this machine can result in an accident.
Assign a supervisor to direct worksite operations. Agree on all safety measures, procedures, and
suitable hand signals.
Failure to comply could result in death or serious injury.

W0287A

CAUTION

Pinch hazard!
Always use suitable tools to align mating parts. DO NOT use your hand or fingers.
Failure to comply could result in minor or moderate injury.

C0044A

Personal Protective Equipment (PPE)

WARNING

Avoid injury!
Use Personal Protective Equipment (PPE), including protective goggles, gloves, and safety footwear.
Failure to comply could result in death or serious injury.

W1036A

Lifting operation

WARNING

Crushing hazard!
The lifting systems must be operated by qualified personnel who are aware of the correct procedures
to follow. Make sure all lifting equipment is in good condition, and all hooks are equipped with safety
latches.
Failure to comply could result in death or serious injury.

W0256A

WARNING

Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.

W0398A

WARNING

Improper operation or service of this machine can result in an accident.
Raised equipment or machine movement without an operator can cause serious injury. Always do the
following before performing any maintenance:
Park the machine on flat, level ground.
Lower the attachment to the ground.
Shut down the engine and remove the ignition key.
Lock the tracks.
Failure to comply could result in death or serious injury.

W0944D

48139695 11/05/2017

6

Summary of Contents for CX33C























Reviews: