background image

1001-4

 Lep 7-27691EN

Issued 02-06

SAFETY

This symbol means ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED. The message that follows the
symbol contains important information about safety. Carefully
read the message. Make sure you fully understand the
causes of possible injury or death.

!

To prevent injury always follow the Warning, Caution
and Danger notes in this section and throughout the
manual.

Put the warning tag shown below on the key for the
keyswitch when servicing or repairing the machine.
One warning tag is supplied with each machine.
Additional tags Part Number 331-4614 are available
from your service parts supplier

.

WARNING:

Read the operator’s manual to

familiarize yourself with the correct control
functions.

!

WARNING:

Operate the machine and

equipment controls from the seat position
only. Any other method could result in
serious injury.

!

WARNING:

This is a one man machine, no

riders allowed.

 

!

WARNING:

Before starting engine, study

Operator’s Manual safety messages. Read
all safety signs on machine. Clear the area of
other persons. Learn and practice safe use
of controls before operating.
It is your responsibility to understand and
f o l l o w   m a n u f a c t u r e r s   i n s t r u c t i o n s   o n
machine operation, service and to observe
pertinent laws and regulations. Operator’s
and Service Manuals may be obtained from
your Case dealer.

!

WARNING:

If you wear clothing that is too

loose or do not use the correct safety
equipment for your job, you can be injured.
Always wear clothing that will not catch on
objects. Extra safety equipment that can be
required includes hard hat, safety shoes, ear
protection, eye or face protection, heavy
gloves and reflector clothing.

!

WARNING:

When working in the area of the

fan belt with the engine running, avoid loose
clothing if possible, and use extreme caution.

!

WARNING:

When doing checks and tests

on the equipment hydraulics, follow the
procedures as they are written. DO NOT
change the procedure.

!

WARNING:

When putting the hydraulic

cylinders on this machine through the
necessary cycles to check operation or to
remove air from a circuit, make sure all
people are out of the way.

!

Summary of Contents for CX330 TIER III

















Reviews:

Related manuals for CX330 TIER III