Case 570NXT Service Manual Download | Manualshive

Page: 7 / 51

background image

INTRODUCTION

Safety rules

DANGER

Improper operation or service of this machine can result in an accident.
Do not operate this machine or perform any lubrication, maintenance, or repair on it until you have
read and understood the operation, lubrication, maintenance, and repair information.
Failure to comply will result in death or serious injury.

D0010A

WARNING

Maintenance hazard!
Always perform all service procedures punctually at the intervals stated in this manual. This ensures
optimum performance levels and maximum safety during machine operation.
Failure to comply could result in death or serious injury.

W0132A

WARNING

Pressurized system!
Before attempting any service procedure, it is your responsibility to know the number of accumulators
on the machine, and the correct procedure for releasing the pressure of each accumulator.
Failure to comply could result in death or serious injury.

W0136A

NOTICE:

Extreme working and environmental conditions require shortened service intervals.

Use Case fluids, lubricants, and filters for the best protection and performance of your machine. All fluids, lubricants,
and filters must be disposed of in compliance with environmental standards and regulations. Contact your dealer with
any questions regarding the service and maintenance of this machine.

Read the safety decals and information decals on the machine. Read the Operator’s Manual and safety manual.
Understand the operation of the machine before you start any service.

Before you service the machine, put a 'Do Not Operate' tag on the steering wheel or over the key switch. Ensure the
tag is at a location where everyone who might operate or service the machine may see clearly. One tag is included
with your new machine. Additional tags are available from your dealer.

Plastic and resin parts

•

Avoid using gasoline, paint thinner, etc. when cleaning plastic parts, console, instrument cluster, etc.

•

Use only water, mild soap, and a soft cloth when you clean these parts.

•

Using gasoline, thinners, etc. can cause discoloration, cracking, or deformation of the part being cleaned.

47441594 27/09/2012

3

Find manuals at https://best-manuals.com

«
...
5
6
7
8
9
...
»

Summary of Contents for 570NXT




















































Reviews:

No comments

Related manuals for 570NXT

Brand: Case Pages: 51

Brand: jcb Pages: 6

Brand: Tektite Pages: 11

Brand: Toro Pages: 8

Brand: Ametek Pages: 162

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands