Case IH FARMALL 30B, Service Manual

Page: 30 / 41

INTRODUCTION
O RING BOSS END FITTING OR LOCK NUT
Nom. SAE Dash
Size
Thread Size Newton·meters lb/in lb/ft
-6 9/16 - 18 48 to 54 432 to 480
-8 3/4 - 16 70 to 78 612 to 684
-10 7/8 - 14 102 to 114 75 to 84
-12 1-1/16 - 12 142 to 160 105 to 117
-16 1-5/16 - 12 237 to 254 175 to 187
37 DEGREE FLARE FITTING (STEEL HYDRAULIC FITTINGS)
Nom. SAE
Dash Size
Tube OD/Hose ID Thread Size Newton·meters lb/in lb/ft
-2 5/16 - 24 8 to 9 72 to 84
-3 3/8 - 24 11 to 12 96 to 108
-4 6.4 mm 1/4 inch 7/16 - 20 14 to 16 120 to 144
-5 7.9 mm 5/16 inch 1/2 - 20 18 to 21 156 to 192
-6 9.5 mm 3/8 inch 9/16 - 18 27 to 33 240 to 300
-8 12.7 mm 1/2 inch 3/4 - 16 46 - 56 408 to 504
-10 15.9 mm 5/8 inch 7/8 - 14 77 to 85 684 to 756
-12 19.0 mm
3/4 inch 1-1/16 - 12
107 to 119 79 to 88
-14 22.2 mm 7/8 inch 1-3/16 -12 127 to 140 94 to 103
-16 25.4 mm 1.0 inch 1-5/16 - 12 131 to 156 97 to 117
-20 31.8 mm 1-1/4 inch 1-5/8 - 12 197 to 223 145 to 165
-24 38.1 mm 1-1/2 inch 1-7/8 - 12 312 to 338 230 to 250
37 DEGREE FITTINGS
TUBE NUTS FOR 37 DEGREE FLARED FITTINGS O RING BOSS PLUGS
ADJUSTABLE FITTING
LOCKNUTS,
SWIVEL JIC-37° SEATS
TORQUE TORQUE
Size Tubing OD Thread
Size Newton·
Meters Foot
Pounds Newton·
Meters Foot
Pounds
mm
in. Min. Max. Min. Max. Min. Max. Min. Max.
4 6.4 1/4 7/16-20 12 16 9 12 8 14 6 10
5 7.9 5/16 1/2-20 16 20 12 15 14 20 10 15
6 9.5 3/8 9/16-18 29 33 21 24 20 27 15 20
8 12.7 1/2 3/4-16 47 54 35 40 34 41 25 30
10 15.9
5/8 7/8-14
72 79 53 53 47 54 35 40
12 19.1 3/4 1-1/
16-12 104 111 77 82 81 95 60 70
14 22.2 7/8 1-3/
16-12 122 136 90 100 95 109 70 80
16 25.4 1 1-5/
16-12 149 163 110 120 108 122 80 90
20 31.8
1-1/4 1-5/8-12
190 204 140 150 129 158 95 115
These torques are not recommended for tubes of 12.7 mm ( 0.5 in ) OD and larger with wall thickness of 0.89 mm
( 0.035 in ) or less. The torque is specified for 0.89 mm ( 0.035 in ) wall tubes on each application individually. Before
installing and torquing 37° flared fittings, clean the face of the flare and threads with a cleaning solvent or Loctite®
brand cleaner, and apply hydraulic sealant Loctite® 569™ to the 37° flare and the threads. Install fitting, and torque
to specified torque, loosen fitting and re-torque to specifications.
84542385 06/10/2011
25