Case IH Farmall 105U Pro EP Service Manual Download

Page: 702 / 1569

Cab climate control - Air conditioning

7. If the gauge needle remains stationary and the vacuum

is maintained for

3 - 5 min

, close both the high and low

side manifold hand valves, turn off and disconnect the
center hose from the pump. The system is now ready
for charging.

8. If a leak is detected, charge the system with approx-

imately

400 g

(

14.1 oz

) of refrigerant and identify leak

using a leak detector. See

Air conditioning - Leakage

test (50.200)

9. Once the leak is located discharge and recover the re-

frigerant in the system, repair the leak, then repeat the
evacuation procedure.

47735452 03/07/2014

50.1 [50.200] / 7

Summary of Contents for Farmall 105U Pro EP


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Farmall 105U Pro EP

Reviews:

Related manuals for Farmall 105U Pro EP

Brands by name

Popular brands

Case IH Farmall 105U Pro EP, Service Manual

Search results

Summary of Contents for Farmall 105U Pro EP

Reviews:

Related manuals for Farmall 105U Pro EP

Brands by name

Popular brands