background image

4

CAUTION: To reduce the risk of

personal injury, use only the

mounting hardware provided with

the approved outlet box to install

the crossbar mounting bracket.

CROSSBAR MOUNTING BRACKET INSTALLATION

CEILING

WIRING

CROSSBAR

MOUNTING

BRACKET

FLAT

WASHER

GREEN

GROUND

WIRE

CEILING FAN

APPROVED

OUTLET BOX

RIDGE

SIDE

DOWN

CANOPY HARDWARE

CANOPY

CANOPY

HATCH

CANOPY LOCK WASHER (4)

CANOPY SCREW (4)

OUTLET BOX

MOUNTING

HARDWARE

Proceed with installation as follows:

Step 1.

 Route the wires from the ceiling outlet box through

the crossbar mounting bracket center hole. Attach the bracket,
with ground wire and ridges down, to the ceiling fixture out-
let box with the mounting hardware included with the outlet
box.
Using the screwdriver, tighten the screws firmly by 

hand

 only,

being careful not to bend the bracket by over tightening.

CEILING HARDWARE

CROSSBAR

MOUNTING

BRACKET

WIRE NUT (4)

GETTING STARTED

Installing a New Ceiling Fixture Outlet Box

If you do not have an existing fixture located where you wish
to place your Casablanca fan, an approved ceiling fixture
outlet box must be installed and wired.

Using Existing Ceiling Fixture Outlet Box

After turning the power OFF at its source (either circuit breaker
or fuse box), lower the old fixture and disconnect the wiring.
Check the ceiling fixture outlet box to be sure that it is
marked ‘

Approved for ceiling fan mounting

’. If it is not, a new

box must be installed.

Warning: To reduce the risk of fire, electrical shock,
or personal injury, mount to outlet box marked
acceptable for ceiling fan support using the mount-
ing hardware provided with the outlet box.

ADDITIONAL HARDWARE

2

1

/

4

 

x 8-32 ROUNDED

HEAD SCREW (2)

FLAT WASHER (2)

1

 x 8-32 ROUNDED

HEAD SCREW (2)

W

AILEA

TM

WARNING: Damp Location rated fans

require a Ground Fault Interrupter

(GFI).  Use a weather-proof outlet box,

properly connect ground wires, and use

only under a weather-proof structure.

Summary of Contents for WAILEA












Reviews: