manualshive.com logo in svg

Casablanca W-500, Technical Bulletin

Share
Download
Casablanca W-500 Technical Bulletin Download Page 10

Casablanca Fan Co. - Factory Service Department - Technical Library

10

File Name (TBW500ConvertW505.pmd) RAS 05-18-2007

Wall Installation

Step A. Locate a 2x4
wall stud in a conve-
nient location.
Step B. Orient the con-
trol bracket as shown
over the 2x4 stud.

Step C.

 Use the 1”

wood screws in either
the inner or outer mount-
ing holes. Install and
tighten screws by 

hand

only.

Note:

 The wall anchors and

6-32 x 1” screws may be
used in situations where
mounting to a stud is not pos-
sible. Use the inner mount-
ing holes. After securing the
anchor, discard the anchor’s
pointed screws and use the
6-32 decor ovalhead screws
supplied.

Changes or modifications not expressly ap-
proved in writing by Casablanca Fan Co. may
void the user’s authority to operate this equip-
ment.

DECOR OVALHEAD SCREWS

W-505™ CONTROL BRACKET INSTALLATION

This device complies with RSS-210 of Industry Canada. Operation is sub-
ject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.

W-505™ BATTERY INSTALLATION

Install Battery

Press battery into control aligned as
shown.Observe proper polarity. Replace the
battery door.

Remove Battery Door

Turn control on its front.  Twist a coin or use
your finger to unsnap the door 

A

. Lift door

away from control 

B 

and remove

 C

.

Changes or modifications not
expressly approved in writing by
Casablanca Fan Co. may void the
user’s authority to operate this
equipment.

This device complies with RSS-210 of Industry Canada. Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause
undesired operation of the device.

DRYWALL ANCHOR

12V BATTERY

Wall Controls -

 

CONTINUED

Wall Controls -

 

CONTINUED

W-505

™

Summary of Contents for W-500














Reviews:

No comments

Brands by name

Popular brands

Load more brands