background image

Twain

2

RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION! 

Please take a moment to locate the model number and serial number from your fan (see below) and record this 
information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear there already. 
These numbers are found on the motor identification plate affixed to the fan motor in the location shown below:

PLEASE INSPECT ALL PACKAGING PRIOR TO DISCARDING!

Your Casablanca fan was crafted with pride and care and inspected thoroughly prior 
to shipment. Before you begin to assemble and install your Casablanca fan, remove all 
parts from the carton and check them against the Parts Guide in this manual.

Make sure all parts are included in the box 
using the Parts Guide on the following pages. 

If there are missing or broken parts: 

Call 1-888-227-2178 Monday through Friday, 

• 

7 a.m. to 4 p.m. PST. Your request will be 
handled immediately. Replacement parts 
will be sent to you via Federal Express.

Proper Parts Handling

Do not remove lightbulbs from their packaging 

• 

until you are ready to install them. 

Before discarding packaging materials, be 

• 

certain that all parts have been removed. 

Use a clean, dry paintbrush to remove small 

• 

Styrofoam pieces that may remain after unpacking.

Do not brush Styrofoam into wiring cavities. 

• 

The blades in each pack are matched for 

• 

equal weight to assure smooth fan operation. 
If more than one fan is being installed, do 
not mix blades from different cartons. 

When cleaning, painting, or working near your 

• 

fan, be cautious of the fan and blades.

Always turn power to the ceiling fan OFF before 

• 

replacing lightbulbs or working on your fan. 

Never insert anything into the path of the 

• 

fan blades while the fan is in operation. 

Never install a fan over a pool or spa. 

• 

Never operate a fan that has been 

• 

damaged in any way. 

Install the fan according to the 
instructions in this manual.

If the fan does not work:

Refer to the Troubleshooting Tips 

• 

in this Owner’s Manual.

Call Technical Support at 1-888-227-2178.

• 

Contact your local Authorized Service Center.

• 

Our Web site at www.casablancafanco.com contains 
additional information on Casablanca products, 
troubleshooting, and Authorized Dealer or Service 
Centers. Please do not return this product to the store.

Serial Number

Model Number

Twain

®

 

TYPE 

  HANGER TYPE

DJ01 1151      MODEL #

C25G624F

POMONA, CA

 SERIAL No.: 

DJ06 2237

       

C25G624F

Motor Identification Plate

Summary of Contents for Twain























Reviews: