background image

www.CasablancaFanCo.com

1.888.227.2178

4

M8516-01 • 11/11/13 • © Casablanca Fan Company

If you have an angled ceiling:

1. You will need a longer downrod

 (sold separately)

.

2. If your ceiling angle is greater than 34°, you

 will  

     also need an Angled Mounting Kit 

(sold separately)

.

 

Guide Touches 

BOTH 

Ceiling & Wall

SI

TU

AT

IO

N 1

 

 

Guide Touches Wall

but

 

NOT

 Ceiling

SI

TU

AT

IO

N 2

You need 

BOTH

 

a Longer 

Downrod & 

an Angled 

Mounting Kit

You need 

ONLY

 

a Longer 

Downrod

*most common

If you have a flat ceiling:

Hang your fan by a standard downrod 

(included)

.

Mounting Options

Support 

Structure

Ceiling 

Outlet Box 

(required)

Angled 

Mounting 

Style

Standard 

Mounting 

Style

Support 

Structure

Ceiling 

Outlet Box 

(required)

Use 

Standard Mounting

 

or 

Low-Profile Mounting

 

to hang the fan from a flat ceiling.

Use 

Angled Mounting

 

to hang the fan from a 

vaulted or angled ceiling. 

4

34

O

CEILING

WA
LL

OPTION 

1

Standard

Mounting

OPTION 

2

Angled 
Mounting

2

3

SLIDE

 

toward ceiling

PLACE

 

against wall

1

FOLD

 

on dotted line

34°

Use the three steps below to determine if your ceiling angle is greater than 34°

1.888.227.2178

M8516-01 • 11/11/13 • © Casablanca Fan Company

Summary of Contents for M8516-01
















Reviews: