SHENZHEN FLUING INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [email protected]
INPUT.
2) Connect the positive pole of lamp to terminal "B
（
+
）
" of OUTPUT, and connect the negative pole of lamp to terminal "A
（
-
）
" of OUTPUT.
Setting different control modes:
We have set the receiver in toggle mode before delivery, if you want to use other modes, do as following operation.
1) Setting control mode Toggle (with transmitter CC-2): Turn on the first bit of the dip switch.
Control mode Toggle: Press -> On; Press again -> Off.
Press the first button of the transmitter: Terminal A and B of OUT1 output AC power, the lamp 1 is turned on.
Press the first button again: Terminal A and B of OUT1 stop outputting, the lamp 1 is turned off.
Press the second button of the transmitter: Terminal A and B of OUT2 output AC power, the lamp 2 is turned on.
Press the second button again: Terminal A and B of OUT2 stop outputting, the lamp 2 is turned off.
2) Setting control mode Momentary (with transmitter CC-2): Turn on the first and the second bits of the dip switch.
Control mode Momentary: Press and hold -> On; Release -> Off.
Press and hold the first button of the transmitter: Terminal A and B of OUT1 output AC power, the lamp 1 is turned on.
Release the first button: Terminal A and B of OUT1 stop outputting, the lamp 1 is turned off.
Press and hold the second button of the transmitter: Terminal A and B of OUT2 output AC power, the lamp 2 is turned on.
Release the second button: Terminal A and B of OUT2 stop outputting, the lamp 2 is turned off.
3) Setting control mode Latched (with transmitter CC-4): Turn on the second bit of the dip switch
Control mode Latched: Press -> On, other relays Off; Press another button -> Off.
Press the button A of the transmitter: Terminal A and B of OUT1 output AC power, the lamp 1 is turned on;
And Terminal A and B of OUT2 stop outputting, the lamp 2 is turned off.
Press the button B of the transmitter: Terminal A and B of OUT2 output AC power, the lamp 2 is turned on;
Terminal A and B of OUT1 stop outputting, the lamp 1 is turned off.
Press the button C of the transmitter: Terminal A and B of OUT1 and OUT2 stop outputting, two lamps are turned off.
Wired control terminals:
The receiver has wired control terminals, you can connect external devices, sensors, limit switches or manual switches to trigger the receiver.
1) By low level signal:
You can connect external devices (with low level output signal) to trigger the receiver.
When external device outputs low level signal to terminals 1 () and terminal 3 (Signal -), terminal A and B of OUT1 output DC power, and the
lamp 1 is turned on.
When the external device stops to output signal, Terminal A and B of OUT1 stop outputting, the lamp 1 is turned off.
When the external device outputs low level signal to manual terminal 2 and terminal 3, Terminal A and B of OUT2 output DC power, the lamp 2 is
turned on
When the external device stops to output signal, Terminal A and B of OUT2 stop outputting, the lamp 2 is turned off.
2) By NO/NC contact:
You can connect manual switches (with NO/NC contact) to trigger the receiver.
When connect terminals 1 and 3 by manual switch, Terminal A and B of OUT1 output DC power, the lamp 1 is turned on.
when disconnect terminals 1 and 3 by manual switch, Terminal A and B of OUT1 stop outputting, the lamp 1 is turned off.
When connect terminals 2 and 3 by manual switch, Terminal A and B of OUT2 output DC power, the lamp 2 is turned on.
And when disconnect terminals 2 and 3 by manual switch, Terminal A and B of OUT2 stop outputting, the lamp 2 is turned off.
Setting feedback function
:
If you want to switch on the feedback function, you need to turn on the third bit of the dip switch.
When the receiver gets the signal of transmitter, it will immediately send a return signal to the transmitter. When the transmitter receive the feedback
signal of the receiver, the transmitter will exude a buzzing sound like
“D~” which means it receive the feedback signal successfully.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is turned on. The receiver starts the LEARNING procedure.
2) Press any one button on transmitter, if signal LED flashes twice, it means learning is successful.
3) The receiver can learn several transmitters with different codes.
Delete all transmitters:
We have learned remote control to
the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the learning button of receiver until signal LED flashes three times. That means all stored codes have been deleted
successfully.
