Cary Audio Design CAD-280 SA V-12R Operation Manual Download Page 2

Specifications for your new

V-12R

 

power amplifier.

We have updated the V-12 mono and  stereo  models  to  a  RACING  (R)

 

version!  The

new 

racing

  input  circuit  makes  the  input  sensitivity  1.2  volts,  similar  to  most

components currently available. Operating the power amplifier is a simple  procedure.
Each unit is designed for long term stability  in  virtually  any home  operating  situation.
Please  note,  if  the  unit  is  operated  outside  the  parameters  outlined  in  this  owner's
manual, damage may result.  Please read this manual carefully before putting your new
V-12R  in  operation.  The  following  definitions  are  applicable.  Warnings  should  be
followed explicitly.

1.2 Specifications

The CAD-280 SA V-12R or V-12R Monobloc version basic specifications:

DIMENSIONS: 

9’’H x 12 _’’W x 20’’D

WEIGHT: 

68-lb. stereo or 85-lb. for the Monobloc version

CIRCUIT TYPE: 

Push-Pull Triode or Ultra-linear Amplification in Pure Class A

POWER OUTPUT: 

50 watts – Triode Mode

100 watts – Triode (Mono)

                             

100 watts – Ultralinear Mode

200 watts – Ultralinear (Mono)

INPUT SENSITIVITY: 

1.3 volts for full output

INPUT IMPEDANCE: 

150,000 ohms

NOISE AND HUM: 

> 84db below rated output

FREQUENCY RESPONSE: 

20Hz to 23Khz +/- 1.0 dB (at full power)     

TUBES:  

2- 12BZ7 Input tubes (or 12AY7, 12AX7)

             

2- EL-84 Current Source tubes (or 6BQ5)

            

12- EL-34 Output tubes (or 6550, KT-66, KT-77, KT-88, KT-

90, 6L6)

POWER TRANSFORMER: 

1- EI laminated, 200% duty cycle

OUTPUT TRANSFORMERS: 

2-EI laminated stereo (1-EI mono) Silicon Impregnated

RESISTORS: 

1.0% tolerance, precision metal film resistors

CAPACITORS: 

Oil Filled

POWER SUPPLY CAPACITORS:  4 - 560 MFD @ 400 volts

AC CORD: 

3 conductor shielded detachable

AC POWER REQUIREMENTS: 

117/234 volts AC 50/60Hz

POWER CONSUMPTION: 

420 watts in operation, 10 watts in stand-by

WARM-UP TIME: 

3 minutes

BREAK-IN PERIOD: 

100 hours of music playing time

FINISH:  

Jaguar Carnival Red paint on chassis

FRONT PANEL: 

Machined, Black Anodized aluminum

Specifications are subject to improvement without notice or obligation.

 

WARNING

HAZARD PRESENTS PERSONAL INJURY OR DEATH

Caution

EQUIPMENT DAMAGE MAY OCCUR BUT NOT PERSONAL INJURY

Note

Proper performance of the amplifier cannot be ensured

if disregarded

Summary of Contents for CAD-280 SA V-12R









Reviews: