Cary Audio Design CAD 211 AE Owner'S Manual Download Page 6

FEATURES_______________________________________________ 

 

Front Panel 

.................................................................................................................................................................................................................. 

CAT EYE TUBE

 

Indicates approximate power output level 

 

When the eye is completely closed the amplifier is at full power output 

.................................................................................................................................................................................................................. 

 

 
Top Panel 

.................................................................................................................................................................................................................. 

OFF-ON TOGGLE SWITCH

  Turns AC power on in the rear position 

 

The output tube will not light at this point 

.................................................................................................................................................................................................................. 

STANDBY SWITCH

 

 Turns the filament of the output tube on in the rear position 

.................................................................................................................................................................................................................. 

 

 

Rear Apron Features 

.................................................................................................................................................................................................................. 

INPUT

 

Signal input connection via shielded RCA interconnect cable 

.................................................................................................................................................................................................................. 

OUTPUT

 

Three 5-way binding posts provide output to the speaker  

 

 

system (4, 8 or 16 ohm connections) 

.................................................................................................................................................................................................................. 

FUSE

 

AC power fuse. Never replace with any other value than  

 

4 AMP SLOW BLOW FUSE! 250 VOLT! 

.................................................................................................................................................................................................................. 

TUBE FUSE

 

Never replace with any other fuse than 1/2 amp FAST BLOW FUSE! 

.................................................................................................................................................................................................................. 

 

5

Summary of Contents for CAD 211 AE
















Reviews: