Cary Audio Design 7.250 Owner'S Manual Download Page 14

OPERATIONS 

 

 

 

Your new Model 7.250 power amplifier is ready for operation after the speaker and the 

interconnect cables have been installed into their proper sockets. 

 

REMOTE TRIGGER POWER ON 

 

How to make connections for remote power-on using components equipped with a 

DC trigger jack: 

 

Using an accessory cable with a 1/8” mono mini-plug and the correct connector specified for your 

source device, follow the procedure below to connect the trigger-output jack on the rear of the 

source device to the Model 7.250 rear panel TRIGGER INPUT. 

 

To install the Trigger Cable: 

 

 

Power the controlling source and amplifier off. 

 

 

Connect the trigger cable to the controlling source and the amplifier. 

 

 

After the connections are made, power on the controlling source and then the amplifier. 

After the source unit is fully powered up, the LED on the amplifier should be in the ON 

state, BLUE DISPLAY. If the amplifier is in the standby mode, press the power button on 

the front panel until the amplifier is in the ON state, BLUE DISPLAY. 

 

 

Verify the trigger is working by putting the source unit into standby mode. The amplifier 

after a short delay will also go into the standby mode. 

 

 

Once you have verified that the trigger cable is working, only use the source unit to 

power on and off your amplifier. 

 

 

 

When installing the trigger cable, never have the controlling source or amplifier 

powered on. Doing so will cause the trigger device to work improperly and could 

cause damage to both the source and amplifier. 

 

 

 

POWER CONNECTION SAFETY 

 

After all audio and system connections have been made, connect the power cord to an AC power 

source. Be sure that the Model 7.250 is powered off and that the device connected to the remote 

trigger input is off when connecting the power cord and plugging it into an AC outlet. 

13

Summary of Contents for 7.250
























Reviews: