manualshive.com logo in svg

Cary Audio Design 7.125, Owner'S Manual

Share
Download
Cary Audio Design 7.125 Owner'S Manual Download Page 17

SPECIFICATIONS 

 

 

15 

Operating the Model 7.125 is a simple procedure. It is designed for long term stability in 
virtually any home operating environment. However, if the unit is operated outside the 
parameters outlined in this Owner's Manual, damage may result. Please read this manual 
carefully before putting your new Model 7.125 power amplifier into operation. 
 
The following section describes the Model 7.125 power amplifier’s basic specifications. 
The specifications are subject to change without notice or obligation. 

 

................................................................................................................................................ 

Audio Input 

7 RCA, 7 XLR 

................................................................................................................................................ 

Audio Output  

 

7 pairs of heavy-duty, gold-plated binding posts 

................................................................................................................................................ 

Power Output 

 

7 x 125w RMS @ 8 ohms 

7 x 190w RMS @ 4 ohms 

from 20Hz to 20KHz   

from 20Hz to 20KHz 

................................................................................................................................................ 

Frequency Response  

20Hz - 20KHz +/- 0.1 dB 

................................................................................................................................................ 

THD   

 

 

Less than 0.05% at rated output 

................................................................................................................................................ 

Signal-to-Noise Ratio 

Greater than 100dB below full rated power A-weighted. 

................................................................................................................................................ 

Crosstalk  

 

 

Greater than -90dB from 20Hz to 20KHz 

................................................................................................................................................ 

Damping Factor 

 

Greater than 400 from 10Hz to 400Hz 

................................................................................................................................................ 

Slew Rate 

 

 

50V/mSec 

................................................................................................................................................ 

Input Sensitivity 

 

1.0v for rated output 

................................................................................................................................................ 

Input Impedance 

 

Nominal 50K ohms 

................................................................................................................................................ 

Gain

 

Voltage Gain of 28dB 

................................................................................................................................................ 

Remote Trigger 

 

3-32v DC at 5mA or greater 

................................................................................................................................................ 

Power Requirements 

 

117/234 Volts AC @ 50/60 Hz 

................................................................................................................................................ 

Dimensions

   

 

7.0” H x 17.7”W x 16.6”D 

................................................................................................................................................ 

Weight 

 

 

55lbs. 

................................................................................................................................................ 

Rock Mounting 

Optional brackets are available for mounting the amplifier 
in a standard 19 inch equipment rack. 

................................................................................................................................................ 

 

Summary of Contents for 7.125


























Reviews:

No comments

Brands by name

Popular brands

Load more brands