CARVIN ENGINEERING DATA
UX SERIES
WIRELESS MICROPHONE SYSTEM
PG.
2
WARRANTY
This CARVIN AUDIO product is guaranteed in normal use to be free from electrical and mechanical defects
for a period of ninety days from date of purchase. Retain proof of purchase. This warranty is in lieu of any and
all other guarantees or warranties, expressed or implied. There shall be no recovery for any consequential or
incidental damages.
INTRODUCTION
Congratulations on your purchase of the UX
Series UHF Professional Modular Wireless
System. The following models are included in
this user manual:
UX1200R UX600B
UX600MC UX-GT
UX-LP1
UX1200R Specifications
»
Operating RF Frequency: 506-542 MHz
»
RF Frequency Bandwidth: 36 MHz
»
Total Frequency Settings : 1441 (25MHz increment)
»
Simultaneous Operation: Up to 14 Channels
»
S/N ratio : 105dB
»
Image frequency rejection : >60dB
»
Audio Output : XLR and 1/4-Inch
»
Output Impedance : 600 Ohms
»
Power Requirement : 12VDC, 500mA (AC adapter included
»
Net Weight : Base 2.4 lbs Receiver
»
Dimensions : 8.35”W x 5.66”D x 1.51”H
UX600B
»
Input Connector Mini 4-Pin XLR (TA4F)
»
Audio Freq. Response 40-18kHz
»
RF Power Output 10mW or 50mW Setting
»
Frequency Deviation ± 48kHz
»
Spurious Emissions < -50 dBC
»
Battery AA 1.5V Alkaline Qty 2
»
Dimensions 2.45” x 3.875”x 0.94” (w/o clip or ant.)
»
Net Wt (no battery) 2.5 oz
UX600M
»
Polar Pattern Unidirectional
»
Audio Freq. Response 50-16kHz
»
RF Power Output 10mW or 50mW setting
»
Battery AA 1.5V Alkaline Qty 2
»
Current Consumption 30 mA typical
»
Battery Life Approx. 25 Hours
»
Dimensions 10.3”L x 1.97” dia.
»
Net Wt (no battery) 12.5 oz
»
GETTING STARTED QUICKLY
»
If you’re like most new owners, you’re probably in a
hurry to use your wireless system. To start, you must
have the receiver (Carvin UX1200R), a transmitter (Carvin
UX600M handheld mic, or the Carvin UX600B with a
compatible mic Performer1 Series, UX-LP1 or UX-GT
cable plugged into an instrument), an XLR or 1/4” cable,
and a sound system or instrument amplifier to hear the
signal through.
»
1. TRANSMITTER CONNECTIONS: Insert 2 fresh AA
alkaline batteries into the transmitter. For the UX600B
belt pack, connect the headset mic, lavalier mic, or cable
and instrument to the belt-pack.
»
2. RECEIVER CONNECTIONS (UX1200R): Attach the 2
included antennas to the connectors on the rear of the
unit. Connect the included AC adapter to the UX1200R,
then plug it into the proper AC power. Using an XLR cable
or shielded 1/4” cable, connect one of the UX1200R
outputs to your sound system or instrument amplifier.
»
3. RECEIVER POWER ON: Turn down the VOLUME of the
UX1200R and the system it is connected to. On the front
right of the UX1200R, press the POWER button.
»
4. TRANSMITTER POWER ON: Press the power button
on the end of the UX600M mic or on the top of the
UX600B belt-pack transmitter. The LCD display should
turn on. (when ON: a quick press of the power button will
turn MUTE on/off, HOLD to turn OFF.)
»
5. CHANNEL VERIFY: Check that both the transmitter
and receiver display the same Group-Channel setting.
To change Group and Channel on UX1200R or UX600M/
UX600B: Hold in the SET button until the display shows
SETTING for one second, then the first digit (Group) will
be blinking. Use the UP/DOWN buttons to match the
Group on the transmitter and receiver. Press SET to have
the second digit (Channel) blinking, then use the UP/
DOWN buttons to match the channel. Press SET to save
and exit. If using multiple systems, each transmitter/
receiver pair must be set to a different group/channel
setting.
»
6. SOUND CHECK: Use the mic or play the instrument as
intended. Set the VOLUME on the front of the UX1200R
to a low level (about 9 o’clock). Gradually raise the output
levels on the sound system or amp to a comfortable
volume. If distortion occurs and the UX1200R front panel
“AF” audio level meter is showing Orange or Red LEDs
then lower the transmitter levels: UX600M(dB setting),
UX600B (SENSIT and ATT settings). If distortion is still
heard, try lowering the preamp level on your sound
system or amp. You can also lower the UX1200R output
by -20dB with the “Att ON” output attenuation setting.
Summary of Contents for UX600B
Page 1: ...WIRELESS SYSTEM UX SERIES...
