USM16-BP BELT-PACK TRANSMITTER
1. BATTERY INSTALLATION/BELT CLIP
Fig A.
A metal belt clip case protects
the transmitter and features a heavy-duty clip. To access the rear controls, push the
two side release buttons on the belt clip. Slide the transmitter up to reveal the rear
AF Gain control.
Push the two side release buttons on the belt clip. Slide the transmitter down to
reveal the battery compartment. Insert fresh AA alkaline batteries, observing cor-
rect polarity as marked inside the battery compartment. Push up until the belt clip
locks.
2. SENSITIVITY
Fig B.
The transmitter's sensitivity controls are located on the
rear. Use the mini screwdriver to first set the Sensitivity switch to 0 for instruments
or -20 for microphones. Use the mini screwdriver to make fine gain adjustments to
the Sensitivity AF Gain for optimal transmitter volume. Decrease the gain if distor-
tion is heard.
3. BATTERY/POWER INDICATOR
Fig C.
The GREEN indicator should light
when the transmitter is ON. With fresh batteries it will shine strongly. As the batter-
ies weaken, the indicator will grow dimmer. When the indicator becomes very dim
or goes out, replace the batteries for continued operation. Expect about 25 hours of
use from a set of alkaline batteries.
4. CHANNEL SELECTOR
Fig C.
The transmitter has 16 different channels. If you
encounter signal interference, try selecting an alternate channel. Make sure the receiv-
er is set to the same channel as the transmitter. Use a small flat-head screwdriver to
change the channel.
5. INPUT CONNECTOR
Fig D.
The mini XLR input jack will connect a Lavaliere
mic, headset mic, or instrument cable to the transmitter. Line up the notches on the
side of the jack and plug. Push in until the cable locks into the jack. To unplug the
mini XLR cable, press the round release button on the cable to unlock it from the
jack.
6. TRANSMITTER ON SWITCH
Fig D.
Turn the receiver volume down before
turning the transmitter power ON. The transmitter ON-OFF switch is located at the
top of the unit. In the ON position, the GREEN indicator
Fig B
should illuminate.
UX-HM2 HEADSET MIC (OPTION)
1. CONNECTION
Fig D. & Fig. F
Connect the mic cable to the transmitter’s mini XLR input jack. Place the mic on vocalist head.
Keep the mic a minimum of 2 inches from the mouth. Adjust the mic position to minimize air
from hitting the mic.
UX-LP1 LAVALIERE MIC (OPTION)
1. CONNECTION
Fig D. & Fig. G
Connect the lavaliere mic cable to the transmitter’s mini XLR input jack.
Clip the mic to a shirt. For optimum sound, position the mic as close to the mouth with the top of the mic fac-
ing up. Test out various positions along the center of the chest to determine the ideal mic placement. This may
vary from person to person as each voice projects uniquely.
UX-GT INSTRUMENT CABLE (OPTION)
1. CABLE CONNECTION
Fig D.
Connect the cable to the belt-pack trans-
mitter’s mini XLR input jack. Plug the
1/4” connector into a guitar. Turn the
receiver volume down before turning the
transmitter power ON.
USM16-MC HAND HELD MIC
1. BATTERY INSTALLATION
Fig H.
While holding the lower part of the transmitter body, unscrew the windscreen ball on top of the
mic. Press the release clip to eject the battery dock. Install fresh AA alkaline batteries. Replace
the battery dock and make sure the clip snaps into the locked position so the battery dock won’t
slide out. Match the 4 pins on the mic handle to the windscreen ball and turn clockwise until
tight.
2. POWER ON AND CHANNEL SELECT
Fig H.
Squeeze the release tab on the top of the mic end cap. Pull the cap off to reveal the power
switch and channel selector. Make sure to turn the receiver volume down before turning the mic
power ON. The Green LED indicates the mic is ON. Turn the volume up on the receiver to set
your level. Make sure the receiver is set to the same channel as the mic. Use a small flat-head
screwdriver to change the channel.
USMBP TRANSMITTER
USM16-MC HAND HELD MIC
UX-HM2 HEAD MIC
Removable
Battery dock
Remove cap to turn ON and
select channel
Push and
slide
transmitter up
Fig. C
Green Power
Indicator
Channel
Selector
Fig. F
Fig. G
Fig. H
Fig. D
Top View
Push the
round
button to
release
the cable
Transmitter
ON/OFF switch
UX-LP1 LAVALIERE MIC
Sensitivity
-20 -6 0
GAIN
Set to 0 for
instruments
Set to -20 for mics
fine gain
settings
Push and slide
transmitter up
Push and slide
transmitter up
Push and slide
transmitter up
Fig. B
Fig. A
