RECEIVER USM16
Receiving System
Diversity- PLL Synthesized
Stability
± 0.005%
Signal-to-noise
>100 dB
Image Rejection
>60 dB
THD
<1% @ 1kHz
RF Sensitivity
-107dBµ for 12 dB S/N AD
Connection
20 pin PCB edgecard, 0.156” pitch.
Audio Output
-12 dBu / 600 ohm through conn.
Power Supply
Power through connector only
Dimensions
W: 3.30” (84mm)
H: 1.22” (31 mm)
D: 5.375” (136.5 mm) to PCB,
4.88” (124mm) to case.
Net Weight
1 lbs (.5 kgs)
Accessories
USM-KIT (REQUIRED for
mounting, holds up to 2 receivers)
Warranty
90 days
INTRODUCTION
Congratulations on your purchase of the USM16 SERIES Professional Modular Wireless
System. The USM16 system is available pre-mounted in certain Carvin mixers, or may be
purchased for self-installation with the USM16-KIT (consult Carvin for compatibility).
Your system includes a receiver along with a handheld mic with transmitter (USM16-MC)
or a belt-pack transmitter (USM16-BP) depending on the model purchased. The headworn
mic (UX-HM2), cable for instrument (UX-GT) and Lavaliere mic (UX-LP1) are all available
as additional options to the USM16-BP belt-pack system.
The receiver features true UHF diversity reception. Two antennas feed two completely
independent RF receivers on the same frequency. Automatic logic circuitry continuously
compares and selects the superior signal to provide better sound quality and reduce the
possibility of interference and dropouts. Both the transmitter and receiver have 16 user
selectable channels.
The versatile USM16-BP belt-pack transmitter is designed for use with condenser micro-
phones as well as Hi-Z line instrument pickups. Please note that in multiple-system appli-
cations there must be one transmitter per receiver.
BELT PACK TRANSMITTER USM16BP
RF Power Output
3 mW
Spurious Rejection
< -60 dBC
Stability
± 0.005%
Frequency Deviation
± 48kHz
Battery
AA 1.5v alkaline qty 2
S/N Ratio
>100dB (1kHz-A)
Current Consumption
100mA typical
Dimensions
2.56” W x 4” H x 1” D
Net Wt (no battery)
2.8 oz (78 grams)
Warranty
90 days
HANDHELD MIC TRANSMITTER
USM16MC
Polar Pattern
Unidirectional
RF Power Output
3 mW
Spurious Emissions
Under federal regulations
Dynamic Range
>100 dB
Battery
AA 1.5v alkaline qty 2
Current Consumption
30 mA typical
Battery Life
Approx. 25 hours
Dimensions
9.50” long, 2.10” dia.
Net Wt (no battery)
12.7 oz (360 grams)
Accessory Included
mic clip
Warranty
90 days
12340 World Trade Drive, San Diego, CA 92128
GETTING STARTED QUICKLY
If you’re like most new owners, you’re probably in a hurry to use your wireless system. To
start, you must have a USM16 compatible Carvin product, at least one USM16 receiver, and
the USM16-KIT (includes mounting hardware, circuit board and antennas).
If you have purchased this system seperately, please start with the installation procedure on
the back page of this manual.
If the unit has been pre-installed from the factory, you can follow these brief instructions to
get you going quickly;
1.
BATTERY
Insert 2 fresh AA alkaline batteries into the transmitter.
2.
CHANNEL CHECK
Check that both the transmitter and receiver are set to corre-
sponding channel. If multiple systems are used, each system must be set to their own
channel.
3
.
BELT PACK SETTINGS
(USM16BP only) Connect the instrument cable or mic to the
Belt-pack. Set the rear gain switch to -20 for mic or 0 for instrument use. Set the fine
gain control to 12 o’clock. Reduce if distortion occurs.
4.
RECEIVER POWER ON
Turn the Volume control of the receiver down and turn down
the volume on the unit this system is mounted in. Make sure you are plugged in to the
proper AC voltage and turn the power ON. This will power on the USM-16 receiver.
5.
TRANSMITTER POWER ON
Switch the mic or belt-pack transmitter to the “ON”
position. The red “RF” LED on the USM-16 should turn on.
6.
SOUND CHECK
Do a sound check and gradually raise the levels while watching the
AF level indicator. Increase the level until the AF level indicator peaks. This indicates that
maximum transmitter modulation without distortion has been reached. You can adjust
the AF level of the transmitter using the included small screwdriver.
RECEIVING INSPECTION—read before getting started
INSPECT YOUR WIRELESS SYSTEM FOR ANY DAMAGE which may have occurred during
shipping. If any damage is found, please notify the shipping company and CARVIN immedi-
ately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your unit,
always use the original carton and packing material. This will provide the best possible pro-
tection during shipment. CARVIN and the shipping company are not liable for any damage
caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately.
Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual for your
records. Keep your portion of the card and return the portion with your name and comments to us.
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
REGULATIONS AND SERVICING
This device complies with part 15 of the FCC Rules. Operation is subject to the condi-
tion that this device does not cause harmful interference.
This device complies with INDUSTRY CANADA R.S.S. 210, en conformite´
avec IC: RSS-210/CNR210.
CAUTION! Electrical shock can result from removal of the receiver cover. Refer servicing
to qualified service personnel. No user-serviceable parts inside. Do not expose to rain or
moisture. The circuits inside the receiver and transmitter have been precisely adjusted
for optimum performance and compliance with federal regulations. Do not attempt to
open the receiver or transmitter. To do so will void the warranty, and may cause improp-
er operation.
CARVIN ENGINEERING DATA
c
WARRANTY
90 days on all electronic components. Does not cover cable connectors or broken parts
caused by normal wear or abuse.
USM16BP/USM16MC WIRELESS SYSTEMS
OPERATING MANUAL
USM16 1209
